Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M16 x 1.5 A4-80 Marine Stainless Torque & Tap Drill Spec

ISO 3506-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
240.837 N·m
177.632 ft-lbs | 2131.59 in-lbs | 24.5586 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
75.262 kN
16,919.5 lbf
Target tension across joint interface
75% Tap Drill d - P
14.5 mm
14.5 mm (92.4% Eng.)
50% Hard Metal Drill: 15.188 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M16 x 1.5 A4-80 Marine Stainless bolt is 240.837 N·m (177.632 ft-lbs) when dry (K=0.20) and 180.628 N·m (133.224 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 75.262 kN (16,919.5 lbf) at 75% proof load. Standard 75% tap drill is 14.5 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 16 mm (0.6299") P = 1.5 mm M16 x 1.5 Close: 17mm Normal: 17.5mm Loose: 18.5mm
Stress Area (As) 167.248 mm²
Pitch Diameter (d2) 15.026 mm
Minor Diameter (d1) 14.376 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (16 − 0.9382 × 1.5)² = 167.248 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 167.248 mm² × 600 N/mm² = 100349 N (100.349 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 100349 N = 75262 N (75.262 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 16 mm × 75262 N) / 1000 = 240.837 N·m (177.632 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M16 x 1.5 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M16 x 1.5
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 240.837 Nm
177.632 ft-lb
216.753 Nm
159.869 ft-lb
180.628 Nm
133.224 ft-lb
144.502 Nm
106.579 ft-lb
75.262 100.349
Class 10.9 333.158 Nm
245.725 ft-lb
299.842 Nm
221.152 ft-lb
249.869 Nm
184.294 ft-lb
199.895 Nm
147.435 ft-lb
104.112 138.816
Class 12.9 389.353 Nm
287.172 ft-lb
350.418 Nm
258.455 ft-lb
292.015 Nm
215.379 ft-lb
233.612 Nm
172.303 ft-lb
121.673 162.231
A2-70 Stainless 180.628 Nm
133.224 ft-lb
162.565 Nm
119.902 ft-lb
135.471 Nm
99.918 ft-lb
108.377 Nm
79.935 ft-lb
56.446 75.262
A4-80 Marine Stainless CURRENT 240.837 Nm
177.632 ft-lb
216.753 Nm
159.869 ft-lb
180.628 Nm
133.224 ft-lb
144.502 Nm
106.579 ft-lb
75.262 100.349

Frequently Asked Engineering Questions (M16 x 1.5 A4-80 Marine Stainless)

What is the recommended tightening torque for a M16 x 1.5 A4-80 Marine Stainless bolt?
For a M16 x 1.5 Stainless Steel A4-80 (AISI 316 / Marine Grade / EN 1.4401) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 240.837 N·m (177.632 ft-lbs / 2131.59 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 180.628 N·m (133.224 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 144.502 N·m (106.579 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M16 x 1.5 internal threads?
The standard cut tap drill size for M16 x 1.5 is 14.5 mm (0.5709" / 14.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 15.188 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M16 x 1.5 A4-80 Marine Stainless fastener develop?
With a tensile stress area (As) of 167.248 mm² (0.25924 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M16 x 1.5 A4-80 Marine Stainless fastener possesses an ultimate proof load of 100.349 kN (22,559.3 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 75.262 kN (16,919.5 lbf) across the joint interface.
What clearance hole diameters should be drilled for M16 x 1.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M16 x 1.5 fastener are: Close Fit = 17 mm (0.6693"), Normal Fit = 17.5 mm (0.689"), and Loose Fit = 18.5 mm (0.7283"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.