Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M18 x 2.5 Class 8.8 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
311.805 N·m
229.975 ft-lbs | 2759.7 in-lbs | 31.7952 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
86.612 kN
19,471.2 lbf
Target tension across joint interface
75% Tap Drill d - P
15.5 mm
15.5 mm (92.4% Eng.)
50% Hard Metal Drill: 16.647 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M18 x 2.5 Class 8.8 bolt is 311.805 N·m (229.975 ft-lbs) when dry (K=0.20) and 233.853 N·m (172.481 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 86.612 kN (19,471.2 lbf) at 75% proof load. Standard 75% tap drill is 15.5 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 18 mm (0.7087") P = 2.5 mm M18 x 2.5 Close: 19mm Normal: 20mm Loose: 21mm
Stress Area (As) 192.472 mm²
Pitch Diameter (d2) 16.376 mm
Minor Diameter (d1) 15.294 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (18 − 0.9382 × 2.5)² = 192.472 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 192.472 mm² × 600 N/mm² = 115483 N (115.483 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 115483 N = 86612 N (86.612 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 18 mm × 86612 N) / 1000 = 311.805 N·m (229.975 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M18 x 2.5 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M18 x 2.5
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 CURRENT 311.805 Nm
229.975 ft-lb
280.624 Nm
206.978 ft-lb
233.853 Nm
172.481 ft-lb
187.083 Nm
137.985 ft-lb
86.612 115.483
Class 10.9 431.33 Nm
318.132 ft-lb
388.197 Nm
286.319 ft-lb
323.497 Nm
238.599 ft-lb
258.798 Nm
190.879 ft-lb
119.814 159.752
Class 12.9 504.084 Nm
371.793 ft-lb
453.676 Nm
334.614 ft-lb
378.063 Nm
278.845 ft-lb
302.451 Nm
223.076 ft-lb
140.023 186.698
A2-70 Stainless 233.853 Nm
172.481 ft-lb
210.468 Nm
155.233 ft-lb
175.39 Nm
129.361 ft-lb
140.312 Nm
103.489 ft-lb
64.959 86.612
A4-80 Marine Stainless 311.805 Nm
229.975 ft-lb
280.624 Nm
206.978 ft-lb
233.853 Nm
172.481 ft-lb
187.083 Nm
137.985 ft-lb
86.612 115.483

Frequently Asked Engineering Questions (M18 x 2.5 Class 8.8)

What is the recommended tightening torque for a M18 x 2.5 Class 8.8 bolt?
For a M18 x 2.5 ISO Metric Property Class 8.8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 311.805 N·m (229.975 ft-lbs / 2759.7 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 233.853 N·m (172.481 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 187.083 N·m (137.985 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M18 x 2.5 internal threads?
The standard cut tap drill size for M18 x 2.5 is 15.5 mm (0.6102" / 15.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 16.647 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M18 x 2.5 Class 8.8 fastener develop?
With a tensile stress area (As) of 192.472 mm² (0.29833 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M18 x 2.5 Class 8.8 fastener possesses an ultimate proof load of 115.483 kN (25,961.7 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 86.612 kN (19,471.2 lbf) across the joint interface.
What clearance hole diameters should be drilled for M18 x 2.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M18 x 2.5 fastener are: Close Fit = 19 mm (0.748"), Normal Fit = 20 mm (0.7874"), and Loose Fit = 21 mm (0.8268"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.