M18 x 2.5 A4-80 Marine Stainless Torque & Tap Drill Spec
ISO 3506-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
311.805 N·m
229.975 ft-lbs | 2759.7 in-lbs | 31.7952 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
86.612 kN
19,471.2 lbf
Target tension across joint interface
75% Tap Drill d - P
15.5 mm
15.5 mm (92.4% Eng.)
50% Hard Metal Drill: 16.647 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M18 x 2.5 A4-80 Marine Stainless bolt is 311.805 N·m (229.975 ft-lbs) when dry (K=0.20) and 233.853 N·m (172.481 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 86.612 kN (19,471.2 lbf) at 75% proof load. Standard 75% tap drill is 15.5 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 192.472 mm²
Pitch Diameter (d2) 16.376 mm
Minor Diameter (d1) 15.294 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (18 − 0.9382 × 2.5)² = 192.472 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 192.472 mm² × 600 N/mm² = 115483 N (115.483 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 115483 N = 86612 N (86.612 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 18 mm × 86612 N) / 1000 = 311.805 N·m (229.975 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M18 x 2.5 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 311.805 Nm 229.975 ft-lb | 280.624 Nm 206.978 ft-lb | 233.853 Nm 172.481 ft-lb | 187.083 Nm 137.985 ft-lb | 86.612 | 115.483 |
| Class 10.9 | 431.33 Nm 318.132 ft-lb | 388.197 Nm 286.319 ft-lb | 323.497 Nm 238.599 ft-lb | 258.798 Nm 190.879 ft-lb | 119.814 | 159.752 |
| Class 12.9 | 504.084 Nm 371.793 ft-lb | 453.676 Nm 334.614 ft-lb | 378.063 Nm 278.845 ft-lb | 302.451 Nm 223.076 ft-lb | 140.023 | 186.698 |
| A2-70 Stainless | 233.853 Nm 172.481 ft-lb | 210.468 Nm 155.233 ft-lb | 175.39 Nm 129.361 ft-lb | 140.312 Nm 103.489 ft-lb | 64.959 | 86.612 |
| A4-80 Marine Stainless CURRENT | 311.805 Nm 229.975 ft-lb | 280.624 Nm 206.978 ft-lb | 233.853 Nm 172.481 ft-lb | 187.083 Nm 137.985 ft-lb | 86.612 | 115.483 |
Frequently Asked Engineering Questions (M18 x 2.5 A4-80 Marine Stainless)
What is the recommended tightening torque for a M18 x 2.5 A4-80 Marine Stainless bolt?
For a M18 x 2.5 Stainless Steel A4-80 (AISI 316 / Marine Grade / EN 1.4401) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 311.805 N·m (229.975 ft-lbs / 2759.7 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 233.853 N·m (172.481 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 187.083 N·m (137.985 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M18 x 2.5 internal threads?
The standard cut tap drill size for M18 x 2.5 is 15.5 mm (0.6102" / 15.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 16.647 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M18 x 2.5 A4-80 Marine Stainless fastener develop?
With a tensile stress area (As) of 192.472 mm² (0.29833 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M18 x 2.5 A4-80 Marine Stainless fastener possesses an ultimate proof load of 115.483 kN (25,961.7 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 86.612 kN (19,471.2 lbf) across the joint interface.
What clearance hole diameters should be drilled for M18 x 2.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M18 x 2.5 fastener are: Close Fit = 19 mm (0.748"), Normal Fit = 20 mm (0.7874"), and Loose Fit = 21 mm (0.8268"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.