Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M20 x 2.5 Class 10.9 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
609.537 N·m
449.571 ft-lbs | 5394.86 in-lbs | 62.1555 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
152.384 kN
34,257.3 lbf
Target tension across joint interface
75% Tap Drill d - P
17.5 mm
17.5 mm (92.4% Eng.)
50% Hard Metal Drill: 18.647 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M20 x 2.5 Class 10.9 bolt is 609.537 N·m (449.571 ft-lbs) when dry (K=0.20) and 457.153 N·m (337.179 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 152.384 kN (34,257.3 lbf) at 75% proof load. Standard 75% tap drill is 17.5 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 20 mm (0.7874") P = 2.5 mm M20 x 2.5 Close: 21mm Normal: 22mm Loose: 24mm
Stress Area (As) 244.794 mm²
Pitch Diameter (d2) 18.376 mm
Minor Diameter (d1) 17.294 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (20 − 0.9382 × 2.5)² = 244.794 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 244.794 mm² × 830 N/mm² = 203179 N (203.179 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 203179 N = 152384 N (152.384 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 20 mm × 152384 N) / 1000 = 609.537 N·m (449.571 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M20 x 2.5 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M20 x 2.5
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 440.629 Nm
324.991 ft-lb
396.566 Nm
292.492 ft-lb
330.472 Nm
243.744 ft-lb
264.378 Nm
194.995 ft-lb
110.157 146.876
Class 10.9 CURRENT 609.537 Nm
449.571 ft-lb
548.583 Nm
404.614 ft-lb
457.153 Nm
337.179 ft-lb
365.722 Nm
269.743 ft-lb
152.384 203.179
Class 12.9 712.351 Nm
525.403 ft-lb
641.115 Nm
472.863 ft-lb
534.263 Nm
394.052 ft-lb
427.41 Nm
315.242 ft-lb
178.088 237.45
A2-70 Stainless 330.472 Nm
243.744 ft-lb
297.425 Nm
219.369 ft-lb
247.854 Nm
182.808 ft-lb
198.283 Nm
146.246 ft-lb
82.618 110.157
A4-80 Marine Stainless 440.629 Nm
324.991 ft-lb
396.566 Nm
292.492 ft-lb
330.472 Nm
243.744 ft-lb
264.378 Nm
194.995 ft-lb
110.157 146.876

Frequently Asked Engineering Questions (M20 x 2.5 Class 10.9)

What is the recommended tightening torque for a M20 x 2.5 Class 10.9 bolt?
For a M20 x 2.5 ISO Metric Property Class 10.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 609.537 N·m (449.571 ft-lbs / 5394.86 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 457.153 N·m (337.179 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 365.722 N·m (269.743 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M20 x 2.5 internal threads?
The standard cut tap drill size for M20 x 2.5 is 17.5 mm (0.6890" / 17.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 18.647 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M20 x 2.5 Class 10.9 fastener develop?
With a tensile stress area (As) of 244.794 mm² (0.37943 in²) and a nominal proof stress of 830 MPa (1,20,381 psi), a M20 x 2.5 Class 10.9 fastener possesses an ultimate proof load of 203.179 kN (45,676.5 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 152.384 kN (34,257.3 lbf) across the joint interface.
What clearance hole diameters should be drilled for M20 x 2.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M20 x 2.5 fastener are: Close Fit = 21 mm (0.8268"), Normal Fit = 22 mm (0.8661"), and Loose Fit = 24 mm (0.9449"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.