M20 x 2.5 A2-70 Stainless Torque & Tap Drill Spec
ISO 3506-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
330.472 N·m
243.744 ft-lbs | 2924.92 in-lbs | 33.6988 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
82.618 kN
18,573.3 lbf
Target tension across joint interface
75% Tap Drill d - P
17.5 mm
17.5 mm (92.4% Eng.)
50% Hard Metal Drill: 18.647 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M20 x 2.5 A2-70 Stainless bolt is 330.472 N·m (243.744 ft-lbs) when dry (K=0.20) and 247.854 N·m (182.808 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 82.618 kN (18,573.3 lbf) at 75% proof load. Standard 75% tap drill is 17.5 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 244.794 mm²
Pitch Diameter (d2) 18.376 mm
Minor Diameter (d1) 17.294 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (20 − 0.9382 × 2.5)² = 244.794 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 244.794 mm² × 450 N/mm² = 110157 N (110.157 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 110157 N = 82618 N (82.618 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 20 mm × 82618 N) / 1000 = 330.472 N·m (243.744 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M20 x 2.5 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 440.629 Nm 324.991 ft-lb | 396.566 Nm 292.492 ft-lb | 330.472 Nm 243.744 ft-lb | 264.378 Nm 194.995 ft-lb | 110.157 | 146.876 |
| Class 10.9 | 609.537 Nm 449.571 ft-lb | 548.583 Nm 404.614 ft-lb | 457.153 Nm 337.179 ft-lb | 365.722 Nm 269.743 ft-lb | 152.384 | 203.179 |
| Class 12.9 | 712.351 Nm 525.403 ft-lb | 641.115 Nm 472.863 ft-lb | 534.263 Nm 394.052 ft-lb | 427.41 Nm 315.242 ft-lb | 178.088 | 237.45 |
| A2-70 Stainless CURRENT | 330.472 Nm 243.744 ft-lb | 297.425 Nm 219.369 ft-lb | 247.854 Nm 182.808 ft-lb | 198.283 Nm 146.246 ft-lb | 82.618 | 110.157 |
| A4-80 Marine Stainless | 440.629 Nm 324.991 ft-lb | 396.566 Nm 292.492 ft-lb | 330.472 Nm 243.744 ft-lb | 264.378 Nm 194.995 ft-lb | 110.157 | 146.876 |
Frequently Asked Engineering Questions (M20 x 2.5 A2-70 Stainless)
What is the recommended tightening torque for a M20 x 2.5 A2-70 Stainless bolt?
For a M20 x 2.5 Stainless Steel A2-70 (AISI 304 / EN 1.4301) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 330.472 N·m (243.744 ft-lbs / 2924.92 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 247.854 N·m (182.808 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 198.283 N·m (146.246 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M20 x 2.5 internal threads?
The standard cut tap drill size for M20 x 2.5 is 17.5 mm (0.6890" / 17.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 18.647 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M20 x 2.5 A2-70 Stainless fastener develop?
With a tensile stress area (As) of 244.794 mm² (0.37943 in²) and a nominal proof stress of 450 MPa (65,267 psi), a M20 x 2.5 A2-70 Stainless fastener possesses an ultimate proof load of 110.157 kN (24,764.3 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 82.618 kN (18,573.3 lbf) across the joint interface.
What clearance hole diameters should be drilled for M20 x 2.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M20 x 2.5 fastener are: Close Fit = 21 mm (0.8268"), Normal Fit = 22 mm (0.8661"), and Loose Fit = 24 mm (0.9449"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.