Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M24 x 3.0 Class 10.9 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
1053.279 N·m
776.859 ft-lbs | 9322.3 in-lbs | 107.4046 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
219.433 kN
49,330.5 lbf
Target tension across joint interface
75% Tap Drill d - P
21 mm
21 mm (92.4% Eng.)
50% Hard Metal Drill: 22.376 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M24 x 3.0 Class 10.9 bolt is 1053.279 N·m (776.859 ft-lbs) when dry (K=0.20) and 789.959 N·m (582.644 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 219.433 kN (49,330.5 lbf) at 75% proof load. Standard 75% tap drill is 21 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 24 mm (0.9449") P = 3 mm M24 x 3.0 Close: 25mm Normal: 26mm Loose: 28mm
Stress Area (As) 352.503 mm²
Pitch Diameter (d2) 22.051 mm
Minor Diameter (d1) 20.752 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (24 − 0.9382 × 3)² = 352.503 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 352.503 mm² × 830 N/mm² = 292577 N (292.577 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 292577 N = 219433 N (219.433 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 24 mm × 219433 N) / 1000 = 1053.279 N·m (776.859 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M24 x 3.0 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M24 x 3.0
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 761.406 Nm
561.585 ft-lb
685.266 Nm
505.426 ft-lb
571.055 Nm
421.188 ft-lb
456.844 Nm
336.951 ft-lb
158.626 211.502
Class 10.9 CURRENT 1053.279 Nm
776.859 ft-lb
947.951 Nm
699.173 ft-lb
789.959 Nm
582.644 ft-lb
631.967 Nm
466.115 ft-lb
219.433 292.577
Class 12.9 1230.94 Nm
907.895 ft-lb
1107.846 Nm
817.106 ft-lb
923.205 Nm
680.921 ft-lb
738.564 Nm
544.737 ft-lb
256.446 341.928
A2-70 Stainless 571.055 Nm
421.188 ft-lb
513.949 Nm
379.07 ft-lb
428.291 Nm
315.891 ft-lb
342.633 Nm
252.713 ft-lb
118.97 158.626
A4-80 Marine Stainless 761.406 Nm
561.585 ft-lb
685.266 Nm
505.426 ft-lb
571.055 Nm
421.188 ft-lb
456.844 Nm
336.951 ft-lb
158.626 211.502

Frequently Asked Engineering Questions (M24 x 3.0 Class 10.9)

What is the recommended tightening torque for a M24 x 3.0 Class 10.9 bolt?
For a M24 x 3.0 ISO Metric Property Class 10.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 1053.279 N·m (776.859 ft-lbs / 9322.3 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 789.959 N·m (582.644 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 631.967 N·m (466.115 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M24 x 3.0 internal threads?
The standard cut tap drill size for M24 x 3.0 is 21 mm (0.8268" / 21 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 22.376 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M24 x 3.0 Class 10.9 fastener develop?
With a tensile stress area (As) of 352.503 mm² (0.54638 in²) and a nominal proof stress of 830 MPa (1,20,381 psi), a M24 x 3.0 Class 10.9 fastener possesses an ultimate proof load of 292.577 kN (65,774 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 219.433 kN (49,330.5 lbf) across the joint interface.
What clearance hole diameters should be drilled for M24 x 3.0 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M24 x 3.0 fastener are: Close Fit = 25 mm (0.9843"), Normal Fit = 26 mm (1.0236"), and Loose Fit = 28 mm (1.1024"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.