M24 x 3.0 Class 8.8 Torque & Tap Drill Spec
ISO 898-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
761.406 N·m
561.585 ft-lbs | 6739.02 in-lbs | 77.6419 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
158.626 kN
35,660.6 lbf
Target tension across joint interface
75% Tap Drill d - P
21 mm
21 mm (92.4% Eng.)
50% Hard Metal Drill: 22.376 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M24 x 3.0 Class 8.8 bolt is 761.406 N·m (561.585 ft-lbs) when dry (K=0.20) and 571.055 N·m (421.188 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 158.626 kN (35,660.6 lbf) at 75% proof load. Standard 75% tap drill is 21 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 352.503 mm²
Pitch Diameter (d2) 22.051 mm
Minor Diameter (d1) 20.752 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (24 − 0.9382 × 3)² = 352.503 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 352.503 mm² × 600 N/mm² = 211502 N (211.502 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 211502 N = 158626 N (158.626 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 24 mm × 158626 N) / 1000 = 761.406 N·m (561.585 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M24 x 3.0 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 CURRENT | 761.406 Nm 561.585 ft-lb | 685.266 Nm 505.426 ft-lb | 571.055 Nm 421.188 ft-lb | 456.844 Nm 336.951 ft-lb | 158.626 | 211.502 |
| Class 10.9 | 1053.279 Nm 776.859 ft-lb | 947.951 Nm 699.173 ft-lb | 789.959 Nm 582.644 ft-lb | 631.967 Nm 466.115 ft-lb | 219.433 | 292.577 |
| Class 12.9 | 1230.94 Nm 907.895 ft-lb | 1107.846 Nm 817.106 ft-lb | 923.205 Nm 680.921 ft-lb | 738.564 Nm 544.737 ft-lb | 256.446 | 341.928 |
| A2-70 Stainless | 571.055 Nm 421.188 ft-lb | 513.949 Nm 379.07 ft-lb | 428.291 Nm 315.891 ft-lb | 342.633 Nm 252.713 ft-lb | 118.97 | 158.626 |
| A4-80 Marine Stainless | 761.406 Nm 561.585 ft-lb | 685.266 Nm 505.426 ft-lb | 571.055 Nm 421.188 ft-lb | 456.844 Nm 336.951 ft-lb | 158.626 | 211.502 |
Frequently Asked Engineering Questions (M24 x 3.0 Class 8.8)
What is the recommended tightening torque for a M24 x 3.0 Class 8.8 bolt?
For a M24 x 3.0 ISO Metric Property Class 8.8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 761.406 N·m (561.585 ft-lbs / 6739.02 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 571.055 N·m (421.188 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 456.844 N·m (336.951 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M24 x 3.0 internal threads?
The standard cut tap drill size for M24 x 3.0 is 21 mm (0.8268" / 21 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 22.376 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M24 x 3.0 Class 8.8 fastener develop?
With a tensile stress area (As) of 352.503 mm² (0.54638 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M24 x 3.0 Class 8.8 fastener possesses an ultimate proof load of 211.502 kN (47,547.5 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 158.626 kN (35,660.6 lbf) across the joint interface.
What clearance hole diameters should be drilled for M24 x 3.0 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M24 x 3.0 fastener are: Close Fit = 25 mm (0.9843"), Normal Fit = 26 mm (1.0236"), and Loose Fit = 28 mm (1.1024"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.