M27 x 3.0 A2-70 Stainless Torque & Tap Drill Spec
ISO 3506-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
837.267 N·m
617.537 ft-lbs | 7410.44 in-lbs | 85.3775 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
155.05 kN
34,856.5 lbf
Target tension across joint interface
75% Tap Drill d - P
24 mm
24 mm (92.4% Eng.)
50% Hard Metal Drill: 25.376 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M27 x 3.0 A2-70 Stainless bolt is 837.267 N·m (617.537 ft-lbs) when dry (K=0.20) and 627.951 N·m (463.153 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 155.05 kN (34,856.5 lbf) at 75% proof load. Standard 75% tap drill is 24 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 459.406 mm²
Pitch Diameter (d2) 25.051 mm
Minor Diameter (d1) 23.752 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (27 − 0.9382 × 3)² = 459.406 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 459.406 mm² × 450 N/mm² = 206733 N (206.733 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 206733 N = 155050 N (155.05 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 27 mm × 155050 N) / 1000 = 837.267 N·m (617.537 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M27 x 3.0 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 1116.357 Nm 823.382 ft-lb | 1004.721 Nm 741.044 ft-lb | 837.267 Nm 617.537 ft-lb | 669.814 Nm 494.029 ft-lb | 206.733 | 275.644 |
| Class 10.9 | 1544.293 Nm 1139.012 ft-lb | 1389.864 Nm 1025.111 ft-lb | 1158.22 Nm 854.259 ft-lb | 926.576 Nm 683.407 ft-lb | 285.98 | 381.307 |
| Class 12.9 | 1804.776 Nm 1331.135 ft-lb | 1624.299 Nm 1198.021 ft-lb | 1353.582 Nm 998.351 ft-lb | 1082.866 Nm 798.681 ft-lb | 334.218 | 445.624 |
| A2-70 Stainless CURRENT | 837.267 Nm 617.537 ft-lb | 753.541 Nm 555.783 ft-lb | 627.951 Nm 463.153 ft-lb | 502.36 Nm 370.522 ft-lb | 155.05 | 206.733 |
| A4-80 Marine Stainless | 1116.357 Nm 823.382 ft-lb | 1004.721 Nm 741.044 ft-lb | 837.267 Nm 617.537 ft-lb | 669.814 Nm 494.029 ft-lb | 206.733 | 275.644 |
Frequently Asked Engineering Questions (M27 x 3.0 A2-70 Stainless)
What is the recommended tightening torque for a M27 x 3.0 A2-70 Stainless bolt?
For a M27 x 3.0 Stainless Steel A2-70 (AISI 304 / EN 1.4301) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 837.267 N·m (617.537 ft-lbs / 7410.44 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 627.951 N·m (463.153 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 502.36 N·m (370.522 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M27 x 3.0 internal threads?
The standard cut tap drill size for M27 x 3.0 is 24 mm (0.9449" / 24 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 25.376 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M27 x 3.0 A2-70 Stainless fastener develop?
With a tensile stress area (As) of 459.406 mm² (0.71208 in²) and a nominal proof stress of 450 MPa (65,267 psi), a M27 x 3.0 A2-70 Stainless fastener possesses an ultimate proof load of 206.733 kN (46,475.4 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 155.05 kN (34,856.5 lbf) across the joint interface.
What clearance hole diameters should be drilled for M27 x 3.0 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M27 x 3.0 fastener are: Close Fit = 28 mm (1.1024"), Normal Fit = 30 mm (1.1811"), and Loose Fit = 32 mm (1.2598"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.