Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M27 x 3.0 Class 12.9 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
1804.776 N·m
1331.135 ft-lbs | 15973.62 in-lbs | 184.036 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
334.218 kN
75,135.2 lbf
Target tension across joint interface
75% Tap Drill d - P
24 mm
24 mm (92.4% Eng.)
50% Hard Metal Drill: 25.376 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M27 x 3.0 Class 12.9 bolt is 1804.776 N·m (1331.135 ft-lbs) when dry (K=0.20) and 1353.582 N·m (998.351 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 334.218 kN (75,135.2 lbf) at 75% proof load. Standard 75% tap drill is 24 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 27 mm (1.063") P = 3 mm M27 x 3.0 Close: 28mm Normal: 30mm Loose: 32mm
Stress Area (As) 459.406 mm²
Pitch Diameter (d2) 25.051 mm
Minor Diameter (d1) 23.752 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (27 − 0.9382 × 3)² = 459.406 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 459.406 mm² × 970 N/mm² = 445624 N (445.624 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 445624 N = 334218 N (334.218 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 27 mm × 334218 N) / 1000 = 1804.776 N·m (1331.135 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M27 x 3.0 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M27 x 3.0
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 1116.357 Nm
823.382 ft-lb
1004.721 Nm
741.044 ft-lb
837.267 Nm
617.537 ft-lb
669.814 Nm
494.029 ft-lb
206.733 275.644
Class 10.9 1544.293 Nm
1139.012 ft-lb
1389.864 Nm
1025.111 ft-lb
1158.22 Nm
854.259 ft-lb
926.576 Nm
683.407 ft-lb
285.98 381.307
Class 12.9 CURRENT 1804.776 Nm
1331.135 ft-lb
1624.299 Nm
1198.021 ft-lb
1353.582 Nm
998.351 ft-lb
1082.866 Nm
798.681 ft-lb
334.218 445.624
A2-70 Stainless 837.267 Nm
617.537 ft-lb
753.541 Nm
555.783 ft-lb
627.951 Nm
463.153 ft-lb
502.36 Nm
370.522 ft-lb
155.05 206.733
A4-80 Marine Stainless 1116.357 Nm
823.382 ft-lb
1004.721 Nm
741.044 ft-lb
837.267 Nm
617.537 ft-lb
669.814 Nm
494.029 ft-lb
206.733 275.644

Frequently Asked Engineering Questions (M27 x 3.0 Class 12.9)

What is the recommended tightening torque for a M27 x 3.0 Class 12.9 bolt?
For a M27 x 3.0 ISO Metric Property Class 12.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 1804.776 N·m (1331.135 ft-lbs / 15973.62 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 1353.582 N·m (998.351 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 1082.866 N·m (798.681 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M27 x 3.0 internal threads?
The standard cut tap drill size for M27 x 3.0 is 24 mm (0.9449" / 24 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 25.376 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M27 x 3.0 Class 12.9 fastener develop?
With a tensile stress area (As) of 459.406 mm² (0.71208 in²) and a nominal proof stress of 970 MPa (1,40,687 psi), a M27 x 3.0 Class 12.9 fastener possesses an ultimate proof load of 445.624 kN (1,00,180.2 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 334.218 kN (75,135.2 lbf) across the joint interface.
What clearance hole diameters should be drilled for M27 x 3.0 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M27 x 3.0 fastener are: Close Fit = 28 mm (1.1024"), Normal Fit = 30 mm (1.1811"), and Loose Fit = 32 mm (1.2598"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.