Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M3 x 0.5 Class 10.9 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
1.879 N·m
1.386 ft-lbs | 16.63 in-lbs | 0.1916 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
3.132 kN
704.1 lbf
Target tension across joint interface
75% Tap Drill d - P
2.5 mm
2.5 mm (92.4% Eng.)
50% Hard Metal Drill: 2.729 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M3 x 0.5 Class 10.9 bolt is 1.879 N·m (1.386 ft-lbs) when dry (K=0.20) and 1.409 N·m (1.039 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 3.132 kN (704.1 lbf) at 75% proof load. Standard 75% tap drill is 2.5 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 3 mm (0.1181") P = 0.5 mm M3 x 0.5 Close: 3.2mm Normal: 3.4mm Loose: 3.6mm
Stress Area (As) 5.031 mm²
Pitch Diameter (d2) 2.675 mm
Minor Diameter (d1) 2.459 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (3 − 0.9382 × 0.5)² = 5.031 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 5.031 mm² × 830 N/mm² = 4176 N (4.176 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 4176 N = 3132 N (3.132 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 3 mm × 3132 N) / 1000 = 1.879 N·m (1.386 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M3 x 0.5 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M3 x 0.5
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 1.358 Nm
1.002 ft-lb
1.223 Nm
0.902 ft-lb
1.019 Nm
0.751 ft-lb
0.815 Nm
0.601 ft-lb
2.264 3.019
Class 10.9 CURRENT 1.879 Nm
1.386 ft-lb
1.691 Nm
1.247 ft-lb
1.409 Nm
1.039 ft-lb
1.127 Nm
0.832 ft-lb
3.132 4.176
Class 12.9 2.196 Nm
1.62 ft-lb
1.976 Nm
1.458 ft-lb
1.647 Nm
1.215 ft-lb
1.318 Nm
0.972 ft-lb
3.66 4.88
A2-70 Stainless 1.019 Nm
0.751 ft-lb
0.917 Nm
0.676 ft-lb
0.764 Nm
0.564 ft-lb
0.611 Nm
0.451 ft-lb
1.698 2.264
A4-80 Marine Stainless 1.358 Nm
1.002 ft-lb
1.223 Nm
0.902 ft-lb
1.019 Nm
0.751 ft-lb
0.815 Nm
0.601 ft-lb
2.264 3.019

Frequently Asked Engineering Questions (M3 x 0.5 Class 10.9)

What is the recommended tightening torque for a M3 x 0.5 Class 10.9 bolt?
For a M3 x 0.5 ISO Metric Property Class 10.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 1.879 N·m (1.386 ft-lbs / 16.63 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 1.409 N·m (1.039 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 1.127 N·m (0.832 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M3 x 0.5 internal threads?
The standard cut tap drill size for M3 x 0.5 is 2.5 mm (0.0984" / 2.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 2.729 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M3 x 0.5 Class 10.9 fastener develop?
With a tensile stress area (As) of 5.031 mm² (0.0078 in²) and a nominal proof stress of 830 MPa (1,20,381 psi), a M3 x 0.5 Class 10.9 fastener possesses an ultimate proof load of 4.176 kN (938.7 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 3.132 kN (704.1 lbf) across the joint interface.
What clearance hole diameters should be drilled for M3 x 0.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M3 x 0.5 fastener are: Close Fit = 3.2 mm (0.126"), Normal Fit = 3.4 mm (0.1339"), and Loose Fit = 3.6 mm (0.1417"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.