M3 x 0.5 Class 8.8 Torque & Tap Drill Spec
ISO 898-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
1.358 N·m
1.002 ft-lbs | 12.02 in-lbs | 0.1385 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
2.264 kN
509 lbf
Target tension across joint interface
75% Tap Drill d - P
2.5 mm
2.5 mm (92.4% Eng.)
50% Hard Metal Drill: 2.729 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M3 x 0.5 Class 8.8 bolt is 1.358 N·m (1.002 ft-lbs) when dry (K=0.20) and 1.019 N·m (0.751 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 2.264 kN (509 lbf) at 75% proof load. Standard 75% tap drill is 2.5 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 5.031 mm²
Pitch Diameter (d2) 2.675 mm
Minor Diameter (d1) 2.459 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (3 − 0.9382 × 0.5)² = 5.031 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 5.031 mm² × 600 N/mm² = 3019 N (3.019 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 3019 N = 2264 N (2.264 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 3 mm × 2264 N) / 1000 = 1.358 N·m (1.002 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M3 x 0.5 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 CURRENT | 1.358 Nm 1.002 ft-lb | 1.223 Nm 0.902 ft-lb | 1.019 Nm 0.751 ft-lb | 0.815 Nm 0.601 ft-lb | 2.264 | 3.019 |
| Class 10.9 | 1.879 Nm 1.386 ft-lb | 1.691 Nm 1.247 ft-lb | 1.409 Nm 1.039 ft-lb | 1.127 Nm 0.832 ft-lb | 3.132 | 4.176 |
| Class 12.9 | 2.196 Nm 1.62 ft-lb | 1.976 Nm 1.458 ft-lb | 1.647 Nm 1.215 ft-lb | 1.318 Nm 0.972 ft-lb | 3.66 | 4.88 |
| A2-70 Stainless | 1.019 Nm 0.751 ft-lb | 0.917 Nm 0.676 ft-lb | 0.764 Nm 0.564 ft-lb | 0.611 Nm 0.451 ft-lb | 1.698 | 2.264 |
| A4-80 Marine Stainless | 1.358 Nm 1.002 ft-lb | 1.223 Nm 0.902 ft-lb | 1.019 Nm 0.751 ft-lb | 0.815 Nm 0.601 ft-lb | 2.264 | 3.019 |
Frequently Asked Engineering Questions (M3 x 0.5 Class 8.8)
What is the recommended tightening torque for a M3 x 0.5 Class 8.8 bolt?
For a M3 x 0.5 ISO Metric Property Class 8.8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 1.358 N·m (1.002 ft-lbs / 12.02 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 1.019 N·m (0.751 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 0.815 N·m (0.601 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M3 x 0.5 internal threads?
The standard cut tap drill size for M3 x 0.5 is 2.5 mm (0.0984" / 2.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 2.729 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M3 x 0.5 Class 8.8 fastener develop?
With a tensile stress area (As) of 5.031 mm² (0.0078 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M3 x 0.5 Class 8.8 fastener possesses an ultimate proof load of 3.019 kN (678.6 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 2.264 kN (509 lbf) across the joint interface.
What clearance hole diameters should be drilled for M3 x 0.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M3 x 0.5 fastener are: Close Fit = 3.2 mm (0.126"), Normal Fit = 3.4 mm (0.1339"), and Loose Fit = 3.6 mm (0.1417"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.