M30 x 3.5 Class 10.9 Torque & Tap Drill Spec
ISO 898-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
2093.789 N·m
1544.299 ft-lbs | 18531.59 in-lbs | 213.507 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
348.965 kN
78,450.4 lbf
Target tension across joint interface
75% Tap Drill d - P
26.5 mm
26.5 mm (92.4% Eng.)
50% Hard Metal Drill: 28.106 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M30 x 3.5 Class 10.9 bolt is 2093.789 N·m (1544.299 ft-lbs) when dry (K=0.20) and 1570.342 N·m (1158.224 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 348.965 kN (78,450.4 lbf) at 75% proof load. Standard 75% tap drill is 26.5 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 560.586 mm²
Pitch Diameter (d2) 27.727 mm
Minor Diameter (d1) 26.211 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (30 − 0.9382 × 3.5)² = 560.586 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 560.586 mm² × 830 N/mm² = 465286 N (465.286 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 465286 N = 348965 N (348.965 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 30 mm × 348965 N) / 1000 = 2093.789 N·m (1544.299 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M30 x 3.5 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 1513.582 Nm 1116.361 ft-lb | 1362.224 Nm 1004.725 ft-lb | 1135.187 Nm 837.271 ft-lb | 908.149 Nm 669.817 ft-lb | 252.264 | 336.352 |
| Class 10.9 CURRENT | 2093.789 Nm 1544.299 ft-lb | 1884.41 Nm 1389.869 ft-lb | 1570.342 Nm 1158.224 ft-lb | 1256.273 Nm 926.58 ft-lb | 348.965 | 465.286 |
| Class 12.9 | 2446.958 Nm 1804.784 ft-lb | 2202.262 Nm 1624.305 ft-lb | 1835.218 Nm 1353.588 ft-lb | 1468.175 Nm 1082.87 ft-lb | 407.826 | 543.768 |
| A2-70 Stainless | 1135.187 Nm 837.271 ft-lb | 1021.668 Nm 753.544 ft-lb | 851.39 Nm 627.953 ft-lb | 681.112 Nm 502.362 ft-lb | 189.198 | 252.264 |
| A4-80 Marine Stainless | 1513.582 Nm 1116.361 ft-lb | 1362.224 Nm 1004.725 ft-lb | 1135.187 Nm 837.271 ft-lb | 908.149 Nm 669.817 ft-lb | 252.264 | 336.352 |
Frequently Asked Engineering Questions (M30 x 3.5 Class 10.9)
What is the recommended tightening torque for a M30 x 3.5 Class 10.9 bolt?
For a M30 x 3.5 ISO Metric Property Class 10.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 2093.789 N·m (1544.299 ft-lbs / 18531.59 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 1570.342 N·m (1158.224 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 1256.273 N·m (926.58 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M30 x 3.5 internal threads?
The standard cut tap drill size for M30 x 3.5 is 26.5 mm (1.0433" / 26.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 28.106 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M30 x 3.5 Class 10.9 fastener develop?
With a tensile stress area (As) of 560.586 mm² (0.86891 in²) and a nominal proof stress of 830 MPa (1,20,381 psi), a M30 x 3.5 Class 10.9 fastener possesses an ultimate proof load of 465.286 kN (1,04,600.5 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 348.965 kN (78,450.4 lbf) across the joint interface.
What clearance hole diameters should be drilled for M30 x 3.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M30 x 3.5 fastener are: Close Fit = 31 mm (1.2205"), Normal Fit = 33 mm (1.2992"), and Loose Fit = 35 mm (1.378"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.