Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M30 x 3.5 Class 12.9 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
2446.958 N·m
1804.784 ft-lbs | 21657.4 in-lbs | 249.5203 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
407.826 kN
91,683 lbf
Target tension across joint interface
75% Tap Drill d - P
26.5 mm
26.5 mm (92.4% Eng.)
50% Hard Metal Drill: 28.106 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M30 x 3.5 Class 12.9 bolt is 2446.958 N·m (1804.784 ft-lbs) when dry (K=0.20) and 1835.218 N·m (1353.588 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 407.826 kN (91,683 lbf) at 75% proof load. Standard 75% tap drill is 26.5 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 30 mm (1.1811") P = 3.5 mm M30 x 3.5 Close: 31mm Normal: 33mm Loose: 35mm
Stress Area (As) 560.586 mm²
Pitch Diameter (d2) 27.727 mm
Minor Diameter (d1) 26.211 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (30 − 0.9382 × 3.5)² = 560.586 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 560.586 mm² × 970 N/mm² = 543768 N (543.768 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 543768 N = 407826 N (407.826 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 30 mm × 407826 N) / 1000 = 2446.958 N·m (1804.784 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M30 x 3.5 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M30 x 3.5
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 1513.582 Nm
1116.361 ft-lb
1362.224 Nm
1004.725 ft-lb
1135.187 Nm
837.271 ft-lb
908.149 Nm
669.817 ft-lb
252.264 336.352
Class 10.9 2093.789 Nm
1544.299 ft-lb
1884.41 Nm
1389.869 ft-lb
1570.342 Nm
1158.224 ft-lb
1256.273 Nm
926.58 ft-lb
348.965 465.286
Class 12.9 CURRENT 2446.958 Nm
1804.784 ft-lb
2202.262 Nm
1624.305 ft-lb
1835.218 Nm
1353.588 ft-lb
1468.175 Nm
1082.87 ft-lb
407.826 543.768
A2-70 Stainless 1135.187 Nm
837.271 ft-lb
1021.668 Nm
753.544 ft-lb
851.39 Nm
627.953 ft-lb
681.112 Nm
502.362 ft-lb
189.198 252.264
A4-80 Marine Stainless 1513.582 Nm
1116.361 ft-lb
1362.224 Nm
1004.725 ft-lb
1135.187 Nm
837.271 ft-lb
908.149 Nm
669.817 ft-lb
252.264 336.352

Frequently Asked Engineering Questions (M30 x 3.5 Class 12.9)

What is the recommended tightening torque for a M30 x 3.5 Class 12.9 bolt?
For a M30 x 3.5 ISO Metric Property Class 12.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 2446.958 N·m (1804.784 ft-lbs / 21657.4 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 1835.218 N·m (1353.588 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 1468.175 N·m (1082.87 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M30 x 3.5 internal threads?
The standard cut tap drill size for M30 x 3.5 is 26.5 mm (1.0433" / 26.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 28.106 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M30 x 3.5 Class 12.9 fastener develop?
With a tensile stress area (As) of 560.586 mm² (0.86891 in²) and a nominal proof stress of 970 MPa (1,40,687 psi), a M30 x 3.5 Class 12.9 fastener possesses an ultimate proof load of 543.768 kN (1,22,244 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 407.826 kN (91,683 lbf) across the joint interface.
What clearance hole diameters should be drilled for M30 x 3.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M30 x 3.5 fastener are: Close Fit = 31 mm (1.2205"), Normal Fit = 33 mm (1.2992"), and Loose Fit = 35 mm (1.378"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.