1018 Mild Carbon Steel (Cold Rolled) — 1/8" (0.125 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 1018 Mild Carbon Steel (Cold Rolled) with a 1/8" (0.125 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 24,061 RPM at 240 m/min (787.4 SFM), with a profiling feed rate of 775 mm/min (30.3 IPM) and adjusted chip load of 0.0161 mm/tooth, achieving a material removal rate of 2.91 cm³/min (0.18 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math1018 Mild Carbon Steel (Cold Rolled) (1/8" (0.125 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3.17 mm | 1.59 mm | 1× | 500 | 19.7 | 2.52 | 0.08 |
| Slotting (100% WOC) | 3F | 3.17 mm | 1.59 mm | 1× | 751 | 29.6 | 3.79 | 0.12 |
| Slotting (100% WOC) | 4F | 3.17 mm | 1.59 mm | 1× | 1,001 | 39.5 | 5.05 | 0.16 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 0.79 mm | 4.76 mm | 1.1565× | 775 | 30.3 | 2.91 | 0.09 |
| Profiling / HEM (25% WOC) | 3F | 0.79 mm | 4.76 mm | 1.1565× | 1,162 | 45.5 | 4.37 | 0.14 |
| Profiling / HEM (25% WOC) | 4F | 0.79 mm | 4.76 mm | 1.1565× | 1,550 | 60.6 | 5.83 | 0.18 |
| Adaptive Clearing (10% WOC) | 2F | 0.32 mm | 6.35 mm | 1.6609× | 1,112 | 43.8 | 2.26 | 0.07 |
| Adaptive Clearing (10% WOC) | 3F | 0.32 mm | 6.35 mm | 1.6609× | 1,667 | 65.7 | 3.39 | 0.11 |
| Adaptive Clearing (10% WOC) | 4F | 0.32 mm | 6.35 mm | 1.6609× | 2,223 | 87.6 | 4.52 | 0.14 |
Shop-Floor Machining Strategy for 1018 Mild Carbon Steel (Cold Rolled)
Work Hardening: ModerateFlood Coolant with 7-9% Soluble Oil or Dry with Air Blast for TiAlN Carbide
Pressure: 5 to 10 bar
With TiAlN coated carbide, dry cutting with air blast prevents thermal shock cycling on cutting edges.
Chip Flow: Low carbon steel can produce continuous gummy stringers if feed rate is too low. Keep chip load elevated.
Milling Direction: Always climb mill to manage tool heat dissipation into chips.
- Avoid rubbing at low feed rates. Feed fast enough to produce C-shaped curled blue/straw chips.
- TiAlN coating thrives on heat; avoid intermittent wet cooling that causes micro-cracking.
- 4-flute end mills deliver the best surface finish and wall straightness.
Frequently Asked CNC Questions (1018 Mild Carbon Steel (Cold Rolled) / 1/8" (0.125 in))
What is the recommended RPM for milling 1018 Mild Carbon Steel (Cold Rolled) with a 1/8" (0.125 in) end mill?
What table feed rate and chip load should I program for 1/8" (0.125 in) in 1018 Mild Carbon Steel (Cold Rolled)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 1018 Mild Carbon Steel (Cold Rolled)?
Recent Calculations
No recent calculations saved yet.