Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

A36 Hot Rolled Structural Steel — 1/8" (0.125 in) 2-Flute Speeds & Feeds

ISO Group P 137 HB / 76 HRB

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
22,056 RPM
Surface Speed: 220 m/min (721.8 SFM)
Table Feed Rate F = RPM·z·fz
671 mm/min
26.5 IPM
Plunge/Ramp Rate: 235 mm/min
Adjusted Chip Load CTF: 1.1565×
0.0152 mm/t
0.0006 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
2.52 cm³/min
0.15 in³/min
Power Required: 0.09 kW (0.12 HP)
Direct CNC Machining Solution

For milling A36 Hot Rolled Structural Steel with a 1/8" (0.125 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 22,056 RPM at 220 m/min (721.8 SFM), with a profiling feed rate of 671 mm/min (26.5 IPM) and adjusted chip load of 0.0152 mm/tooth, achieving a material removal rate of 2.52 cm³/min (0.15 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
A36 Hot Rolled Structural Steel Stock CLIMB D = 3.175 mm (0.125") ae = 0.79 mm ap = 4.76 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1565×
Spindle Torque 0.03 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (220 × 1000) / (π × 3.175) = 22,056 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.79/3.175 = 0.25 → CTF = 1.1565×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0131 mm × 1.1565 = 0.0152 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 22,056 × 2 × 0.0152 = 671 mm/min (26.5 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.76 × 0.79 × 671) / 1000 = 2.52 cm³/min (0.15 in³/min)
Specific Cutting Force (kc) for A36 Hot Rolled Structural Steel: 1650 N/mm². Spindle drive efficiency η = 0.80.

A36 Hot Rolled Structural Steel (1/8" (0.125 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/8" (0.125 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3.17 mm 1.59 mm 1× 432 17.2 2.18 0.07
Slotting (100% WOC) 3F 3.17 mm 1.59 mm 1× 648 25.8 3.27 0.11
Slotting (100% WOC) 4F 3.17 mm 1.59 mm 1× 865 34.4 4.36 0.15
Profiling / HEM (25% WOC) CURRENT 2F 0.79 mm 4.76 mm 1.1565× 671 26.5 2.52 0.09
Profiling / HEM (25% WOC) 3F 0.79 mm 4.76 mm 1.1565× 1,006 39.7 3.78 0.13
Profiling / HEM (25% WOC) 4F 0.79 mm 4.76 mm 1.1565× 1,341 52.9 5.04 0.17
Adaptive Clearing (10% WOC) 2F 0.32 mm 6.35 mm 1.6609× 962 37.9 1.95 0.07
Adaptive Clearing (10% WOC) 3F 0.32 mm 6.35 mm 1.6609× 1,442 56.9 2.93 0.1
Adaptive Clearing (10% WOC) 4F 0.32 mm 6.35 mm 1.6609× 1,923 75.9 3.91 0.13

Shop-Floor Machining Strategy for A36 Hot Rolled Structural Steel

Work Hardening: Moderate
Coolant & Lubrication Protocol

Heavy Flood Coolant with Emulsion

Pressure: 5 to 10 bar

Abrasive black mill scale rapidly destroys cutting edges. Cut beneath the scale on the first pass.

Chip Evacuation & Tool Path Guidance

Chip Flow: Longer chips; ensure adequate chip breaking via aggressive feed rates.

Milling Direction: Climb milling mandatory.

Expert Machinist Tips:
  • CRITICAL: Set first roughing depth of cut at least 1.5 mm to penetrate underneath the abrasive mill scale.
  • Do not skin cut through mill scale; it will instantly dull carbide corner radiuses.
  • Use corner radius end mills (0.5 mm or 0.030" radius) to reinforce cutting corners.

Frequently Asked CNC Questions (A36 Hot Rolled Structural Steel / 1/8" (0.125 in))

What is the recommended RPM for milling A36 Hot Rolled Structural Steel with a 1/8" (0.125 in) end mill?
For a 1/8" (0.125 in) (3.175 mm) TiAlN coated carbide end mill in A36 Hot Rolled Structural Steel, the baseline surface cutting speed is 220 m/min (721.8 SFM), which translates to a calculated spindle speed of 22,056 RPM. If using uncoated carbide, reduce surface speed to 180 m/min (600 SFM / 18046 RPM). For HSS cutters, speed must be restricted to 30 m/min (3008 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/8" (0.125 in) in A36 Hot Rolled Structural Steel?
At 22,056 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0152 mm/tooth (0.0006"/tooth) after applying a radial chip thinning factor (CTF) of 1.1565×. This yields a table feed rate of 671 mm/min (26.5 IPM). Ramping or plunging into material should be limited to 35% of table feed (235 mm/min / 9.3 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.79 mm), the Chip Thinning Factor is 1.1565×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining A36 Hot Rolled Structural Steel?
Heavy Flood Coolant with Emulsion. Pressure specification: 5 to 10 bar. Engineering rationale: Abrasive black mill scale rapidly destroys cutting edges. Cut beneath the scale on the first pass.