17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 1/2" (0.500 in) 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 1/2" (0.500 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 2,757 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 340 mm/min (13.3 IPM) and adjusted chip load of 0.0308 mm/tooth, achieving a material removal rate of 20.53 cm³/min (1.24 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (1/2" (0.500 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 12.7 mm | 6.35 mm | 1× | 111 | 4.4 | 8.95 | 0.48 |
| Slotting (100% WOC) | 3F | 12.7 mm | 6.35 mm | 1× | 166 | 6.5 | 13.39 | 0.73 |
| Slotting (100% WOC) | 4F | 12.7 mm | 6.35 mm | 1× | 222 | 8.7 | 17.9 | 0.97 |
| Profiling / HEM (25% WOC) | 2F | 3.17 mm | 19.05 mm | 1.1553× | 170 | 6.7 | 10.27 | 0.56 |
| Profiling / HEM (25% WOC) | 3F | 3.17 mm | 19.05 mm | 1.1553× | 255 | 10 | 15.4 | 0.83 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 3.17 mm | 19.05 mm | 1.1553× | 340 | 13.3 | 20.53 | 1.11 |
| Adaptive Clearing (10% WOC) | 2F | 1.27 mm | 25.4 mm | 1.6667× | 245 | 9.6 | 7.9 | 0.43 |
| Adaptive Clearing (10% WOC) | 3F | 1.27 mm | 25.4 mm | 1.6667× | 368 | 14.5 | 11.87 | 0.64 |
| Adaptive Clearing (10% WOC) | 4F | 1.27 mm | 25.4 mm | 1.6667× | 491 | 19.3 | 15.84 | 0.86 |
Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)
Work Hardening: HighHigh-Pressure Flood Coolant with Synthetic Water-Soluble Fluid
Pressure: 30 to 70 bar
Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.
Chip Flow: Crisp, tight curled chips; high cutting forces generated.
Milling Direction: Always climb mill.
- In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
- Use thick-core end mills designed for hardened steels (4-5 flutes).
- Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.
Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 1/2" (0.500 in))
What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 1/2" (0.500 in) end mill?
What table feed rate and chip load should I program for 1/2" (0.500 in) in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Recent Calculations
No recent calculations saved yet.