17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 3/16" (0.1875 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 3/16" (0.1875 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 7,353 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 311 mm/min (12.4 IPM) and adjusted chip load of 0.0141 mm/tooth, achieving a material removal rate of 2.64 cm³/min (0.16 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting Math17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (3/16" (0.1875 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4.76 mm | 2.38 mm | 1× | 134 | 5.3 | 1.52 | 0.08 |
| Slotting (100% WOC) | 3F | 4.76 mm | 2.38 mm | 1× | 201 | 7.9 | 2.28 | 0.12 |
| Slotting (100% WOC) | 4F | 4.76 mm | 2.38 mm | 1× | 268 | 10.6 | 3.04 | 0.16 |
| Profiling / HEM (25% WOC) | 2F | 1.19 mm | 7.14 mm | 1.1549× | 207 | 8.2 | 1.76 | 0.1 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1.19 mm | 7.14 mm | 1.1549× | 311 | 12.4 | 2.64 | 0.14 |
| Profiling / HEM (25% WOC) | 4F | 1.19 mm | 7.14 mm | 1.1549× | 415 | 16.5 | 3.53 | 0.19 |
| Adaptive Clearing (10% WOC) | 2F | 0.48 mm | 9.52 mm | 1.6608× | 299 | 11.8 | 1.37 | 0.07 |
| Adaptive Clearing (10% WOC) | 3F | 0.48 mm | 9.52 mm | 1.6608× | 448 | 17.6 | 2.05 | 0.11 |
| Adaptive Clearing (10% WOC) | 4F | 0.48 mm | 9.52 mm | 1.6608× | 597 | 23.5 | 2.73 | 0.15 |
Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)
Work Hardening: HighHigh-Pressure Flood Coolant with Synthetic Water-Soluble Fluid
Pressure: 30 to 70 bar
Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.
Chip Flow: Crisp, tight curled chips; high cutting forces generated.
Milling Direction: Always climb mill.
- In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
- Use thick-core end mills designed for hardened steels (4-5 flutes).
- Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.
Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 3/16" (0.1875 in))
What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 3/16" (0.1875 in) end mill?
What table feed rate and chip load should I program for 3/16" (0.1875 in) in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
Recent Calculations
No recent calculations saved yet.