Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) — 3/8" (0.375 in) 2-Flute Speeds & Feeds

ISO Group M / H 388 HB / 40-42 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
3,676 RPM
Surface Speed: 110 m/min (360.9 SFM)
Table Feed Rate F = RPM·z·fz
180 mm/min
7.1 IPM
Plunge/Ramp Rate: 63 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0245 mm/t
0.00096 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
6.12 cm³/min
0.37 in³/min
Power Required: 0.33 kW (0.44 HP)
Direct CNC Machining Solution

For milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 3/8" (0.375 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 3,676 RPM at 110 m/min (360.9 SFM), with a profiling feed rate of 180 mm/min (7.1 IPM) and adjusted chip load of 0.0245 mm/tooth, achieving a material removal rate of 6.12 cm³/min (0.37 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) Stock CLIMB D = 9.525 mm (0.375") ae = 2.38 mm ap = 14.29 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.7 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (110 × 1000) / (π × 9.525) = 3,676 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2.38/9.525 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0212 mm × 1.1549 = 0.0245 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 3,676 × 2 × 0.0245 = 180 mm/min (7.1 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (14.29 × 2.38 × 180) / 1000 = 6.12 cm³/min (0.37 in³/min)
Specific Cutting Force (kc) for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC): 2600 N/mm². Spindle drive efficiency η = 0.80.

17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) (3/8" (0.375 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/8" (0.375 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 9.53 mm 4.76 mm 1× 117 4.6 5.31 0.29
Slotting (100% WOC) 3F 9.53 mm 4.76 mm 1× 175 6.9 7.94 0.43
Slotting (100% WOC) 4F 9.53 mm 4.76 mm 1× 234 9.3 10.61 0.57
Profiling / HEM (25% WOC) CURRENT 2F 2.38 mm 14.29 mm 1.1549× 180 7.1 6.12 0.33
Profiling / HEM (25% WOC) 3F 2.38 mm 14.29 mm 1.1549× 270 10.6 9.18 0.5
Profiling / HEM (25% WOC) 4F 2.38 mm 14.29 mm 1.1549× 360 14.1 12.24 0.66
Adaptive Clearing (10% WOC) 2F 0.95 mm 19.05 mm 1.6686× 260 10.2 4.71 0.26
Adaptive Clearing (10% WOC) 3F 0.95 mm 19.05 mm 1.6686× 390 15.3 7.06 0.38
Adaptive Clearing (10% WOC) 4F 0.95 mm 19.05 mm 1.6686× 521 20.4 9.43 0.51

Shop-Floor Machining Strategy for 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)

Work Hardening: High
Coolant & Lubrication Protocol

High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid

Pressure: 30 to 70 bar

Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.

Chip Evacuation & Tool Path Guidance

Chip Flow: Crisp, tight curled chips; high cutting forces generated.

Milling Direction: Always climb mill.

Expert Machinist Tips:
  • In H900 condition, tool rigidity and low runout (<0.005 mm) are required to avoid chipped flutes.
  • Use thick-core end mills designed for hardened steels (4-5 flutes).
  • Trochoidal / dynamic milling with light radial engagement (6-10%) increases tool life by 300%.

Frequently Asked CNC Questions (17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) / 3/8" (0.375 in))

What is the recommended RPM for milling 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC) with a 3/8" (0.375 in) end mill?
For a 3/8" (0.375 in) (9.525 mm) TiAlN coated carbide end mill in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC), the baseline surface cutting speed is 110 m/min (360.9 SFM), which translates to a calculated spindle speed of 3,676 RPM. If using uncoated carbide, reduce surface speed to 85 m/min (280 SFM / 2841 RPM). For HSS cutters, speed must be restricted to 14 m/min (468 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/8" (0.375 in) in 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
At 3,676 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0245 mm/tooth (0.00096"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 180 mm/min (7.1 IPM). Ramping or plunging into material should be limited to 35% of table feed (63 mm/min / 2.5 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2.38 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining 17-4 PH Precipitation Hardening Stainless (Condition H900 / 40 HRC)?
High-Pressure Flood Coolant with Synthetic Water-Soluble Fluid. Pressure specification: 30 to 70 bar. Engineering rationale: Heat dissipation from the shear zone prevents thermal tempering and edge fatigue.