Delrin (Acetal / Polyoxymethylene / POM-C) — 3/16" (0.1875 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 3/16" (0.1875 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 33,422 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 3,429 mm/min (135.4 IPM) and adjusted chip load of 0.0342 mm/tooth, achieving a material removal rate of 29.13 cm³/min (1.79 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (3/16" (0.1875 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 4.76 mm | 2.38 mm | 1× | 1,484 | 58.2 | 16.81 | 0.09 |
| Slotting (100% WOC) | 3F | 4.76 mm | 2.38 mm | 1× | 2,226 | 87.2 | 25.22 | 0.13 |
| Slotting (100% WOC) | 4F | 4.76 mm | 2.38 mm | 1× | 2,968 | 116.3 | 33.62 | 0.18 |
| Profiling / HEM (25% WOC) | 2F | 1.19 mm | 7.14 mm | 1.1549× | 2,286 | 90.2 | 19.42 | 0.1 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 1.19 mm | 7.14 mm | 1.1549× | 3,429 | 135.4 | 29.13 | 0.15 |
| Profiling / HEM (25% WOC) | 4F | 1.19 mm | 7.14 mm | 1.1549× | 4,572 | 180.5 | 38.85 | 0.2 |
| Adaptive Clearing (10% WOC) | 2F | 0.48 mm | 9.52 mm | 1.6608× | 3,289 | 129.7 | 15.03 | 0.08 |
| Adaptive Clearing (10% WOC) | 3F | 0.48 mm | 9.52 mm | 1.6608× | 4,933 | 194.5 | 22.54 | 0.12 |
| Adaptive Clearing (10% WOC) | 4F | 0.48 mm | 9.52 mm | 1.6608× | 6,577 | 259.4 | 30.05 | 0.16 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 3/16" (0.1875 in))
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 3/16" (0.1875 in) end mill?
What table feed rate and chip load should I program for 3/16" (0.1875 in) in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.