Delrin (Acetal / Polyoxymethylene / POM-C) — 3 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 3 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 53,052 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 5,029 mm/min (197.4 IPM) and adjusted chip load of 0.0237 mm/tooth, achieving a material removal rate of 16.97 cm³/min (1.03 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (3 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3 mm | 1.5 mm | 1× | 1,634 | 64.7 | 7.35 | 0.04 |
| Slotting (100% WOC) | 3F | 3 mm | 1.5 mm | 1× | 2,451 | 97.1 | 11.03 | 0.06 |
| Slotting (100% WOC) | 4F | 3 mm | 1.5 mm | 1× | 3,268 | 129.4 | 14.71 | 0.08 |
| Profiling / HEM (25% WOC) | 2F | 0.75 mm | 4.5 mm | 1.1547× | 2,515 | 98.7 | 8.49 | 0.04 |
| Profiling / HEM (25% WOC) | 3F | 0.75 mm | 4.5 mm | 1.1547× | 3,772 | 148 | 12.73 | 0.07 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 0.75 mm | 4.5 mm | 1.1547× | 5,029 | 197.4 | 16.97 | 0.09 |
| Adaptive Clearing (10% WOC) | 2F | 0.3 mm | 6 mm | 1.6667× | 3,629 | 143.2 | 6.53 | 0.03 |
| Adaptive Clearing (10% WOC) | 3F | 0.3 mm | 6 mm | 1.6667× | 5,443 | 214.9 | 9.8 | 0.05 |
| Adaptive Clearing (10% WOC) | 4F | 0.3 mm | 6 mm | 1.6667× | 7,258 | 286.5 | 13.06 | 0.07 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 3 mm)
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 3 mm end mill?
What table feed rate and chip load should I program for 3 mm in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.