HDPE (High-Density Polyethylene) — 3/8" (0.375 in) 2-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling HDPE (High-Density Polyethylene) with a 3/8" (0.375 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 15,038 RPM at 450 m/min (1476.4 SFM), with a profiling feed rate of 1,898 mm/min (74.6 IPM) and adjusted chip load of 0.0631 mm/tooth, achieving a material removal rate of 64.55 cm³/min (3.93 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathHDPE (High-Density Polyethylene) (3/8" (0.375 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 9.53 mm | 4.76 mm | 1× | 1,233 | 48.4 | 55.93 | 0.21 |
| Slotting (100% WOC) | 3F | 9.53 mm | 4.76 mm | 1× | 1,850 | 72.6 | 83.92 | 0.31 |
| Slotting (100% WOC) | 4F | 9.53 mm | 4.76 mm | 1× | 2,466 | 96.8 | 111.86 | 0.42 |
| Profiling / HEM (25% WOC) CURRENT | 2F | 2.38 mm | 14.29 mm | 1.1549× | 1,898 | 74.6 | 64.55 | 0.24 |
| Profiling / HEM (25% WOC) | 3F | 2.38 mm | 14.29 mm | 1.1549× | 2,847 | 111.9 | 96.83 | 0.36 |
| Profiling / HEM (25% WOC) | 4F | 2.38 mm | 14.29 mm | 1.1549× | 3,796 | 149.2 | 129.1 | 0.48 |
| Adaptive Clearing (10% WOC) | 2F | 0.95 mm | 19.05 mm | 1.6686× | 2,740 | 108 | 49.59 | 0.19 |
| Adaptive Clearing (10% WOC) | 3F | 0.95 mm | 19.05 mm | 1.6686× | 4,110 | 162 | 74.38 | 0.28 |
| Adaptive Clearing (10% WOC) | 4F | 0.95 mm | 19.05 mm | 1.6686× | 5,480 | 215.9 | 99.17 | 0.37 |
Shop-Floor Machining Strategy for HDPE (High-Density Polyethylene)
Work Hardening: None (Significant thermal expansion coefficient: 10x of steel)Cold Compressed Air Blast or Water Mist
Pressure: 5 bar compressed air
HDPE melts at only 130°C (266°F). Cold air blast is mandatory to prevent gumming.
Chip Flow: Produces fluffy, lightweight, static-charged continuous shavings. High volume vacuum extraction recommended.
Milling Direction: Climb milling prevents feathered edge tears.
- Use razor-sharp single flute O-flute cutters with polished gullets.
- Account for thermal contraction: warm parts measured straight off the CNC machine will shrink when cooled to 20°C room temp.
- Do not allow tool to dwell or friction will melt a pocket into the plastic.
Frequently Asked CNC Questions (HDPE (High-Density Polyethylene) / 3/8" (0.375 in))
What is the recommended RPM for milling HDPE (High-Density Polyethylene) with a 3/8" (0.375 in) end mill?
What table feed rate and chip load should I program for 3/8" (0.375 in) in HDPE (High-Density Polyethylene)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining HDPE (High-Density Polyethylene)?
Recent Calculations
No recent calculations saved yet.