Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Polycarbonate (Lexan / PC Thermoplastic) — 1/4" (0.250 in) 2-Flute Speeds & Feeds

ISO Group O 70 Shore D / 118 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
19,048 RPM
Surface Speed: 380 m/min (1246.7 SFM)
Table Feed Rate F = RPM·z·fz
1,448 mm/min
57.1 IPM
Plunge/Ramp Rate: 507 mm/min
Adjusted Chip Load CTF: 1.1541×
0.038 mm/t
0.0015 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
21.92 cm³/min
1.34 in³/min
Power Required: 0.14 kW (0.18 HP)
Direct CNC Machining Solution

For milling Polycarbonate (Lexan / PC Thermoplastic) with a 1/4" (0.250 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 19,048 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 1,448 mm/min (57.1 IPM) and adjusted chip load of 0.038 mm/tooth, achieving a material removal rate of 21.92 cm³/min (1.34 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Polycarbonate (Lexan / PC Thermoplastic) Stock CLIMB D = 6.35 mm (0.25") ae = 1.59 mm ap = 9.52 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1541×
Spindle Torque 0.06 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (380 × 1000) / (π × 6.35) = 19,048 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.59/6.35 = 0.25 → CTF = 1.1541×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0329 mm × 1.1541 = 0.038 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 19,048 × 2 × 0.038 = 1,448 mm/min (57.1 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (9.52 × 1.59 × 1448) / 1000 = 21.92 cm³/min (1.34 in³/min)
Specific Cutting Force (kc) for Polycarbonate (Lexan / PC Thermoplastic): 300 N/mm². Spindle drive efficiency η = 0.80.

Polycarbonate (Lexan / PC Thermoplastic) (1/4" (0.250 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 1/4" (0.250 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 6.35 mm 3.17 mm 1× 941 37 18.94 0.12
Slotting (100% WOC) 3F 6.35 mm 3.17 mm 1× 1,411 55.4 28.4 0.18
Slotting (100% WOC) 4F 6.35 mm 3.17 mm 1× 1,882 73.9 37.88 0.24
Profiling / HEM (25% WOC) CURRENT 2F 1.59 mm 9.52 mm 1.1541× 1,448 57.1 21.92 0.14
Profiling / HEM (25% WOC) 3F 1.59 mm 9.52 mm 1.1541× 2,171 85.7 32.86 0.21
Profiling / HEM (25% WOC) 4F 1.59 mm 9.52 mm 1.1541× 2,895 114.3 43.82 0.27
Adaptive Clearing (10% WOC) 2F 0.64 mm 12.7 mm 1.6609× 2,080 81.9 16.91 0.11
Adaptive Clearing (10% WOC) 3F 0.64 mm 12.7 mm 1.6609× 3,120 122.9 25.36 0.16
Adaptive Clearing (10% WOC) 4F 0.64 mm 12.7 mm 1.6609× 4,160 163.8 33.81 0.21

Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)

Work Hardening: None (High internal residual stress from extrusion)
Coolant & Lubrication Protocol

Cold Air Blast Only or Pure Deionized Water

Pressure: Cold air gun at 5 bar

CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.

Chip Evacuation & Tool Path Guidance

Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.

Milling Direction: Climb milling mandatory to avoid chipping edge breakout.

Expert Machinist Tips:
  • Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
  • Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
  • Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.

Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 1/4" (0.250 in))

What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 1/4" (0.250 in) end mill?
For a 1/4" (0.250 in) (6.35 mm) TiAlN coated carbide end mill in Polycarbonate (Lexan / PC Thermoplastic), the baseline surface cutting speed is 380 m/min (1246.7 SFM), which translates to a calculated spindle speed of 19,048 RPM. If using uncoated carbide, reduce surface speed to 320 m/min (1050 SFM / 16041 RPM). For HSS cutters, speed must be restricted to 100 m/min (5013 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 1/4" (0.250 in) in Polycarbonate (Lexan / PC Thermoplastic)?
At 19,048 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.038 mm/tooth (0.0015"/tooth) after applying a radial chip thinning factor (CTF) of 1.1541×. This yields a table feed rate of 1448 mm/min (57.1 IPM). Ramping or plunging into material should be limited to 35% of table feed (507 mm/min / 20 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.59 mm), the Chip Thinning Factor is 1.1541×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Cold Air Blast Only or Pure Deionized Water. Pressure specification: Cold air gun at 5 bar. Engineering rationale: CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.