Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Polycarbonate (Lexan / PC Thermoplastic) — 3/16" (0.1875 in) 2-Flute Speeds & Feeds

ISO Group O 70 Shore D / 118 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
25,401 RPM
Surface Speed: 380 m/min (1246.7 SFM)
Table Feed Rate F = RPM·z·fz
1,529 mm/min
60.5 IPM
Plunge/Ramp Rate: 535 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0301 mm/t
0.00119 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
12.99 cm³/min
0.8 in³/min
Power Required: 0.08 kW (0.11 HP)
Direct CNC Machining Solution

For milling Polycarbonate (Lexan / PC Thermoplastic) with a 3/16" (0.1875 in) 2-flute TiAlN carbide end mill, the recommended spindle speed is 25,401 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 1,529 mm/min (60.5 IPM) and adjusted chip load of 0.0301 mm/tooth, achieving a material removal rate of 12.99 cm³/min (0.8 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Polycarbonate (Lexan / PC Thermoplastic) Stock CLIMB D = 4.762 mm (0.1875") ae = 1.19 mm ap = 7.14 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.02 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (380 × 1000) / (π × 4.762) = 25,401 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 1.19/4.762 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0261 mm × 1.1549 = 0.0301 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 25,401 × 2 × 0.0301 = 1,529 mm/min (60.5 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (7.14 × 1.19 × 1529) / 1000 = 12.99 cm³/min (0.8 in³/min)
Specific Cutting Force (kc) for Polycarbonate (Lexan / PC Thermoplastic): 300 N/mm². Spindle drive efficiency η = 0.80.

Polycarbonate (Lexan / PC Thermoplastic) (3/16" (0.1875 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/16" (0.1875 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 4.76 mm 2.38 mm 1× 996 39.1 11.28 0.07
Slotting (100% WOC) 3F 4.76 mm 2.38 mm 1× 1,494 58.7 16.93 0.11
Slotting (100% WOC) 4F 4.76 mm 2.38 mm 1× 1,991 78.2 22.56 0.14
Profiling / HEM (25% WOC) CURRENT 2F 1.19 mm 7.14 mm 1.1549× 1,529 60.5 12.99 0.08
Profiling / HEM (25% WOC) 3F 1.19 mm 7.14 mm 1.1549× 2,294 90.7 19.49 0.12
Profiling / HEM (25% WOC) 4F 1.19 mm 7.14 mm 1.1549× 3,058 120.9 25.98 0.16
Adaptive Clearing (10% WOC) 2F 0.48 mm 9.52 mm 1.6608× 2,200 86.4 10.05 0.06
Adaptive Clearing (10% WOC) 3F 0.48 mm 9.52 mm 1.6608× 3,300 129.5 15.08 0.09
Adaptive Clearing (10% WOC) 4F 0.48 mm 9.52 mm 1.6608× 4,399 172.7 20.1 0.13

Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)

Work Hardening: None (High internal residual stress from extrusion)
Coolant & Lubrication Protocol

Cold Air Blast Only or Pure Deionized Water

Pressure: Cold air gun at 5 bar

CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.

Chip Evacuation & Tool Path Guidance

Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.

Milling Direction: Climb milling mandatory to avoid chipping edge breakout.

Expert Machinist Tips:
  • Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
  • Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
  • Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.

Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 3/16" (0.1875 in))

What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 3/16" (0.1875 in) end mill?
For a 3/16" (0.1875 in) (4.762 mm) TiAlN coated carbide end mill in Polycarbonate (Lexan / PC Thermoplastic), the baseline surface cutting speed is 380 m/min (1246.7 SFM), which translates to a calculated spindle speed of 25,401 RPM. If using uncoated carbide, reduce surface speed to 320 m/min (1050 SFM / 21390 RPM). For HSS cutters, speed must be restricted to 100 m/min (6684 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/16" (0.1875 in) in Polycarbonate (Lexan / PC Thermoplastic)?
At 25,401 RPM with a 2-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0301 mm/tooth (0.00119"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 1529 mm/min (60.5 IPM). Ramping or plunging into material should be limited to 35% of table feed (535 mm/min / 21.2 IPM) at an entry ramp angle of 3°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 1.19 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Cold Air Blast Only or Pure Deionized Water. Pressure specification: Cold air gun at 5 bar. Engineering rationale: CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.