Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Polycarbonate (Lexan / PC Thermoplastic) — 3/8" (0.375 in) 4-Flute Speeds & Feeds

ISO Group O 70 Shore D / 118 Rockwell R

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
12,699 RPM
Surface Speed: 380 m/min (1246.7 SFM)
Table Feed Rate F = RPM·z·fz
2,667 mm/min
105.1 IPM
Plunge/Ramp Rate: 933 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0525 mm/t
0.00207 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
90.71 cm³/min
5.54 in³/min
Power Required: 0.57 kW (0.76 HP)
Direct CNC Machining Solution

For milling Polycarbonate (Lexan / PC Thermoplastic) with a 3/8" (0.375 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 12,699 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 2,667 mm/min (105.1 IPM) and adjusted chip load of 0.0525 mm/tooth, achieving a material removal rate of 90.71 cm³/min (5.54 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Polycarbonate (Lexan / PC Thermoplastic) Stock CLIMB D = 9.525 mm (0.375") ae = 2.38 mm ap = 14.29 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 0.34 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (380 × 1000) / (π × 9.525) = 12,699 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2.38/9.525 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0455 mm × 1.1549 = 0.0525 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 12,699 × 4 × 0.0525 = 2,667 mm/min (105.1 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (14.29 × 2.38 × 2667) / 1000 = 90.71 cm³/min (5.54 in³/min)
Specific Cutting Force (kc) for Polycarbonate (Lexan / PC Thermoplastic): 300 N/mm². Spindle drive efficiency η = 0.80.

Polycarbonate (Lexan / PC Thermoplastic) (3/8" (0.375 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/8" (0.375 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 9.53 mm 4.76 mm 1× 866 34 39.28 0.25
Slotting (100% WOC) 3F 9.53 mm 4.76 mm 1× 1,299 51 58.93 0.37
Slotting (100% WOC) 4F 9.53 mm 4.76 mm 1× 1,732 68.1 78.57 0.49
Profiling / HEM (25% WOC) 2F 2.38 mm 14.29 mm 1.1549× 1,333 52.6 45.34 0.28
Profiling / HEM (25% WOC) 3F 2.38 mm 14.29 mm 1.1549× 2,000 78.9 68.02 0.43
Profiling / HEM (25% WOC) CURRENT 4F 2.38 mm 14.29 mm 1.1549× 2,667 105.1 90.71 0.57
Adaptive Clearing (10% WOC) 2F 0.95 mm 19.05 mm 1.6686× 1,928 75.9 34.89 0.22
Adaptive Clearing (10% WOC) 3F 0.95 mm 19.05 mm 1.6686× 2,892 113.9 52.34 0.33
Adaptive Clearing (10% WOC) 4F 0.95 mm 19.05 mm 1.6686× 3,855 151.9 69.77 0.44

Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)

Work Hardening: None (High internal residual stress from extrusion)
Coolant & Lubrication Protocol

Cold Air Blast Only or Pure Deionized Water

Pressure: Cold air gun at 5 bar

CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.

Chip Evacuation & Tool Path Guidance

Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.

Milling Direction: Climb milling mandatory to avoid chipping edge breakout.

Expert Machinist Tips:
  • Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
  • Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
  • Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.

Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 3/8" (0.375 in))

What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 3/8" (0.375 in) end mill?
For a 3/8" (0.375 in) (9.525 mm) TiAlN coated carbide end mill in Polycarbonate (Lexan / PC Thermoplastic), the baseline surface cutting speed is 380 m/min (1246.7 SFM), which translates to a calculated spindle speed of 12,699 RPM. If using uncoated carbide, reduce surface speed to 320 m/min (1050 SFM / 10694 RPM). For HSS cutters, speed must be restricted to 100 m/min (3342 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/8" (0.375 in) in Polycarbonate (Lexan / PC Thermoplastic)?
At 12,699 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0525 mm/tooth (0.00207"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 2667 mm/min (105.1 IPM). Ramping or plunging into material should be limited to 35% of table feed (933 mm/min / 36.8 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2.38 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Cold Air Blast Only or Pure Deionized Water. Pressure specification: Cold air gun at 5 bar. Engineering rationale: CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.