Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Ti-6Al-4V Titanium Alloy (Grade 5) — 3/8" (0.375 in) 4-Flute Speeds & Feeds

ISO Group S 330 HB / 36 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
2,172 RPM
Surface Speed: 65 m/min (213.3 SFM)
Table Feed Rate F = RPM·z·fz
195 mm/min
7.6 IPM
Plunge/Ramp Rate: 68 mm/min
Adjusted Chip Load CTF: 1.1549×
0.0224 mm/t
0.00088 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
6.63 cm³/min
0.4 in³/min
Power Required: 0.39 kW (0.52 HP)
Direct CNC Machining Solution

For milling Ti-6Al-4V Titanium Alloy (Grade 5) with a 3/8" (0.375 in) 4-flute TiAlN carbide end mill, the recommended spindle speed is 2,172 RPM at 65 m/min (213.3 SFM), with a profiling feed rate of 195 mm/min (7.6 IPM) and adjusted chip load of 0.0224 mm/tooth, achieving a material removal rate of 6.63 cm³/min (0.4 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Ti-6Al-4V Titanium Alloy (Grade 5) Stock CLIMB D = 9.525 mm (0.375") ae = 2.38 mm ap = 14.29 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1549×
Spindle Torque 1.36 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (65 × 1000) / (π × 9.525) = 2,172 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 2.38/9.525 = 0.25 → CTF = 1.1549×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0194 mm × 1.1549 = 0.0224 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 2,172 × 4 × 0.0224 = 195 mm/min (7.6 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (14.29 × 2.38 × 195) / 1000 = 6.63 cm³/min (0.4 in³/min)
Specific Cutting Force (kc) for Ti-6Al-4V Titanium Alloy (Grade 5): 2800 N/mm². Spindle drive efficiency η = 0.80.

Ti-6Al-4V Titanium Alloy (Grade 5) (3/8" (0.375 in)) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3/8" (0.375 in)
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 9.53 mm 4.76 mm 1× 63 2.5 2.86 0.17
Slotting (100% WOC) 3F 9.53 mm 4.76 mm 1× 95 3.7 4.31 0.25
Slotting (100% WOC) 4F 9.53 mm 4.76 mm 1× 127 5 5.76 0.34
Profiling / HEM (25% WOC) 2F 2.38 mm 14.29 mm 1.1549× 97 3.8 3.3 0.19
Profiling / HEM (25% WOC) 3F 2.38 mm 14.29 mm 1.1549× 146 5.7 4.97 0.29
Profiling / HEM (25% WOC) CURRENT 4F 2.38 mm 14.29 mm 1.1549× 195 7.6 6.63 0.39
Adaptive Clearing (10% WOC) 2F 0.95 mm 19.05 mm 1.6686× 141 5.6 2.55 0.15
Adaptive Clearing (10% WOC) 3F 0.95 mm 19.05 mm 1.6686× 211 8.3 3.82 0.22
Adaptive Clearing (10% WOC) 4F 0.95 mm 19.05 mm 1.6686× 281 11.1 5.09 0.3

Shop-Floor Machining Strategy for Ti-6Al-4V Titanium Alloy (Grade 5)

Work Hardening: High
Coolant & Lubrication Protocol

High-Pressure Through-Spindle Flood Coolant (70 bar / 1000 PSI)

Pressure: 70 bar through-spindle coolant mandatory for deep milling

Titanium thermal conductivity is 1/6th of steel; heat cannot dissipate into chips and concentrates directly on the cutting edge. WARNING: Dry titanium chips present a combustible metal fire hazard.

Chip Evacuation & Tool Path Guidance

Chip Flow: Chips weld chemically to tool steel and carbide at elevated temperatures.

Milling Direction: Strict climb milling. Keep radial engagement (ae) under 20% of tool diameter.

Expert Machinist Tips:
  • LOW SPEED, HIGH FEED, ABUNDANT COOLANT: The universal titanium triad.
  • Arc into cuts using a roll-in programmed entry; linear plunges cause tool shock fractures.
  • Never dwell in the cut; program corner deceleration cautiously to prevent tool rubbing.

Frequently Asked CNC Questions (Ti-6Al-4V Titanium Alloy (Grade 5) / 3/8" (0.375 in))

What is the recommended RPM for milling Ti-6Al-4V Titanium Alloy (Grade 5) with a 3/8" (0.375 in) end mill?
For a 3/8" (0.375 in) (9.525 mm) TiAlN coated carbide end mill in Ti-6Al-4V Titanium Alloy (Grade 5), the baseline surface cutting speed is 65 m/min (213.3 SFM), which translates to a calculated spindle speed of 2,172 RPM. If using uncoated carbide, reduce surface speed to 50 m/min (165 SFM / 1671 RPM). For HSS cutters, speed must be restricted to 11 m/min (368 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3/8" (0.375 in) in Ti-6Al-4V Titanium Alloy (Grade 5)?
At 2,172 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0224 mm/tooth (0.00088"/tooth) after applying a radial chip thinning factor (CTF) of 1.1549×. This yields a table feed rate of 195 mm/min (7.6 IPM). Ramping or plunging into material should be limited to 35% of table feed (68 mm/min / 2.7 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 2.38 mm), the Chip Thinning Factor is 1.1549×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Ti-6Al-4V Titanium Alloy (Grade 5)?
High-Pressure Through-Spindle Flood Coolant (70 bar / 1000 PSI). Pressure specification: 70 bar through-spindle coolant mandatory for deep milling. Engineering rationale: Titanium thermal conductivity is 1/6th of steel; heat cannot dissipate into chips and concentrates directly on the cutting edge. WARNING: Dry titanium chips present a combustible metal fire hazard.