Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

Ti-6Al-4V Titanium Alloy (Grade 5) — 3 mm 4-Flute Speeds & Feeds

ISO Group S 330 HB / 36 HRC

Live CNC Milling Parameter Engine

24,000 RPM
mm
mm
m/min
Spindle Speed RPM
6,897 RPM
Surface Speed: 65 m/min (213.3 SFM)
Table Feed Rate F = RPM·z·fz
246 mm/min
9.7 IPM
Plunge/Ramp Rate: 86 mm/min
Adjusted Chip Load CTF: 1.1547×
0.0089 mm/t
0.00035 in/tooth
Thinning compensation applied for light stepover
Material Removal & Power MRR
0.83 cm³/min
0.05 in³/min
Power Required: 0.05 kW (0.06 HP)
Direct CNC Machining Solution

For milling Ti-6Al-4V Titanium Alloy (Grade 5) with a 3 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 6,897 RPM at 65 m/min (213.3 SFM), with a profiling feed rate of 246 mm/min (9.7 IPM) and adjusted chip load of 0.0089 mm/tooth, achieving a material removal rate of 0.83 cm³/min (0.05 in³/min).

Radial Engagement & Chip Thinning Blueprint

DIN 6584 / Sandvik
Ti-6Al-4V Titanium Alloy (Grade 5) Stock CLIMB D = 3 mm (0.1181") ae = 0.75 mm ap = 4.5 mm Workpiece
Radial Ratio (ae/D) 25%
Chip Thinning (CTF) 1.1547×
Spindle Torque 0.06 N·m

Step-by-Step Machining Physics Proof

DIN 6584 Cutting Math
Step 1: Spindle RPM from Cutting Speed (Vc)
RPM = (Vc × 1000) / (π × D)
RPM = (65 × 1000) / (π × 3) = 6,897 RPM
Step 2: Radial Chip Thinning Factor (CTF)
CTF = 1 / √(1 − (1 − 2·(ae/D))²)
ae/D = 0.75/3 = 0.25 → CTF = 1.1547×
Step 3: Adjusted Chip Load (fz,adj)
fz,adj = fz,base × CTF
fz,adj = 0.0077 mm × 1.1547 = 0.0089 mm/tooth
Step 4: Table Feed Rate (F)
F = RPM × z × fz,adj
F = 6,897 × 4 × 0.0089 = 246 mm/min (9.7 IPM)
Step 5: Material Removal Rate (MRR)
MRR = (ap × ae × F) / 1000
MRR = (4.5 × 0.75 × 246) / 1000 = 0.83 cm³/min (0.05 in³/min)
Specific Cutting Force (kc) for Ti-6Al-4V Titanium Alloy (Grade 5): 2800 N/mm². Spindle drive efficiency η = 0.80.

Ti-6Al-4V Titanium Alloy (Grade 5) (3 mm) Cutting Strategy Matrix

Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).

Tool: 3 mm
Operation Strategy Flutes Stepover (ae) Depth (ap) CTF Feed (mm/min) Feed (IPM) MRR (cm³/min) Power (kW)
Slotting (100% WOC) 2F 3 mm 1.5 mm 1× 80 3.2 0.36 0.02
Slotting (100% WOC) 3F 3 mm 1.5 mm 1× 120 4.8 0.54 0.03
Slotting (100% WOC) 4F 3 mm 1.5 mm 1× 160 6.3 0.72 0.04
Profiling / HEM (25% WOC) 2F 0.75 mm 4.5 mm 1.1547× 123 4.8 0.42 0.02
Profiling / HEM (25% WOC) 3F 0.75 mm 4.5 mm 1.1547× 184 7.2 0.62 0.04
Profiling / HEM (25% WOC) CURRENT 4F 0.75 mm 4.5 mm 1.1547× 246 9.7 0.83 0.05
Adaptive Clearing (10% WOC) 2F 0.3 mm 6 mm 1.6667× 177 6.9 0.32 0.02
Adaptive Clearing (10% WOC) 3F 0.3 mm 6 mm 1.6667× 265 10.3 0.48 0.03
Adaptive Clearing (10% WOC) 4F 0.3 mm 6 mm 1.6667× 353 13.8 0.64 0.04

Shop-Floor Machining Strategy for Ti-6Al-4V Titanium Alloy (Grade 5)

Work Hardening: High
Coolant & Lubrication Protocol

High-Pressure Through-Spindle Flood Coolant (70 bar / 1000 PSI)

Pressure: 70 bar through-spindle coolant mandatory for deep milling

Titanium thermal conductivity is 1/6th of steel; heat cannot dissipate into chips and concentrates directly on the cutting edge. WARNING: Dry titanium chips present a combustible metal fire hazard.

Chip Evacuation & Tool Path Guidance

Chip Flow: Chips weld chemically to tool steel and carbide at elevated temperatures.

Milling Direction: Strict climb milling. Keep radial engagement (ae) under 20% of tool diameter.

Expert Machinist Tips:
  • LOW SPEED, HIGH FEED, ABUNDANT COOLANT: The universal titanium triad.
  • Arc into cuts using a roll-in programmed entry; linear plunges cause tool shock fractures.
  • Never dwell in the cut; program corner deceleration cautiously to prevent tool rubbing.

Frequently Asked CNC Questions (Ti-6Al-4V Titanium Alloy (Grade 5) / 3 mm)

What is the recommended RPM for milling Ti-6Al-4V Titanium Alloy (Grade 5) with a 3 mm end mill?
For a 3 mm (3 mm) TiAlN coated carbide end mill in Ti-6Al-4V Titanium Alloy (Grade 5), the baseline surface cutting speed is 65 m/min (213.3 SFM), which translates to a calculated spindle speed of 6,897 RPM. If using uncoated carbide, reduce surface speed to 50 m/min (165 SFM / 5305 RPM). For HSS cutters, speed must be restricted to 11 m/min (1167 RPM) to avoid thermal edge failure.
What table feed rate and chip load should I program for 3 mm in Ti-6Al-4V Titanium Alloy (Grade 5)?
At 6,897 RPM with a 4-flute cutter in standard 25% radial profiling engagement, the adjusted chip load is 0.0089 mm/tooth (0.00035"/tooth) after applying a radial chip thinning factor (CTF) of 1.1547×. This yields a table feed rate of 246 mm/min (9.7 IPM). Ramping or plunging into material should be limited to 35% of table feed (86 mm/min / 3.4 IPM) at an entry ramp angle of 1.5°.
Why does radial chip thinning occur when milling at less than 50% stepover?
When the radial width of cut (ae) is less than 50% of the cutter diameter, the cutting tooth leaves the cut before reaching maximum chip thickness. Without compensation, the effective chip becomes paper-thin, causing the cutter to rub and work-harden rather than shear cleanly. At 25% stepover (ae = 0.75 mm), the Chip Thinning Factor is 1.1547×, requiring a programmed feed increase to maintain the true physical chip thickness and preserve tool life.
What coolant strategy is recommended for CNC machining Ti-6Al-4V Titanium Alloy (Grade 5)?
High-Pressure Through-Spindle Flood Coolant (70 bar / 1000 PSI). Pressure specification: 70 bar through-spindle coolant mandatory for deep milling. Engineering rationale: Titanium thermal conductivity is 1/6th of steel; heat cannot dissipate into chips and concentrates directly on the cutting edge. WARNING: Dry titanium chips present a combustible metal fire hazard.