Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

#10-32 UNF Grade 8 Torque & Tap Drill Spec

SAE J429 / ASTM A354 Grade BD

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
7.726 N·m
5.698 ft-lbs | 68.38 in-lbs | 0.7878 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
8.004 kN
1,799.5 lbf
Target tension across joint interface
75% Tap Drill d - P
4.039 mm
#21 (0.1590 in) (91.6% Eng.)
50% Hard Metal Drill: 4.397 mm
Direct Engineering Specification Summary

The recommended tightening torque for a #10-32 UNF Grade 8 bolt is 7.726 N·m (5.698 ft-lbs) when dry (K=0.20) and 5.794 N·m (4.274 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 8.004 kN (1,799.5 lbf) at 75% proof load. Standard 75% tap drill is #21 (0.1590 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 4.826 mm (0.19") P = 0.79375 mm #10-32 UNF Close: 5.182mm Normal: 5.613mm Loose: 5.944mm
Stress Area (As) 12.899 mm²
Pitch Diameter (d2) 4.31 mm
Minor Diameter (d1) 3.967 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (4.826 − 0.9382 × 0.79375)² = 12.899 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 12.899 mm² × 827.4 N/mm² = 10673 N (10.673 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 10673 N = 8004 N (8.004 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 4.826 mm × 8004 N) / 1000 = 7.726 N·m (5.698 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

#10-32 UNF Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: #10-32 UNF
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 5.473 Nm
4.037 ft-lb
4.925 Nm
3.633 ft-lb
4.105 Nm
3.027 ft-lb
3.284 Nm
2.422 ft-lb
5.67 7.56
Grade 8 CURRENT 7.726 Nm
5.698 ft-lb
6.953 Nm
5.129 ft-lb
5.794 Nm
4.274 ft-lb
4.636 Nm
3.419 ft-lb
8.004 10.673
18-8 Stainless 2.897 Nm
2.137 ft-lb
2.608 Nm
1.923 ft-lb
2.173 Nm
1.603 ft-lb
1.738 Nm
1.282 ft-lb
3.002 4.003

Frequently Asked Engineering Questions (#10-32 UNF Grade 8)

What is the recommended tightening torque for a #10-32 UNF Grade 8 bolt?
For a #10-32 UNF SAE J429 Grade 8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 7.726 N·m (5.698 ft-lbs / 68.38 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 5.794 N·m (4.274 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 4.636 N·m (3.419 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping #10-32 UNF internal threads?
The standard cut tap drill size for #10-32 UNF is #21 (0.1590 in) (0.1590" / 4.039 mm), which delivers approximately 91.6% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 4.397 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a #10-32 UNF Grade 8 fastener develop?
With a tensile stress area (As) of 12.899 mm² (0.01999 in²) and a nominal proof stress of 827.4 MPa (1,20,000 psi), a #10-32 UNF Grade 8 fastener possesses an ultimate proof load of 10.673 kN (2,399.3 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 8.004 kN (1,799.5 lbf) across the joint interface.
What clearance hole diameters should be drilled for #10-32 UNF bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a #10-32 UNF fastener are: Close Fit = 5.182 mm (0.204"), Normal Fit = 5.613 mm (0.221"), and Loose Fit = 5.944 mm (0.234"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.