Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

3/4"-16 UNF Grade 8 Torque & Tap Drill Spec

SAE J429 / ASTM A354 Grade BD

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
568.894 N·m
419.595 ft-lbs | 5035.14 in-lbs | 58.0111 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
149.316 kN
33,567.6 lbf
Target tension across joint interface
75% Tap Drill d - P
17.462 mm
11/16" (0.6875 in) (92.4% Eng.)
50% Hard Metal Drill: 18.191 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 3/4"-16 UNF Grade 8 bolt is 568.894 N·m (419.595 ft-lbs) when dry (K=0.20) and 426.671 N·m (314.696 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 149.316 kN (33,567.6 lbf) at 75% proof load. Standard 75% tap drill is 11/16" (0.6875 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 19.05 mm (0.75") P = 1.5875 mm 3/4"-16 UNF Close: 19.456mm Normal: 19.837mm Loose: 20.65mm
Stress Area (As) 240.619 mm²
Pitch Diameter (d2) 18.019 mm
Minor Diameter (d1) 17.331 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (19.05 − 0.9382 × 1.5875)² = 240.619 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 240.619 mm² × 827.4 N/mm² = 199088 N (199.088 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 199088 N = 149316 N (149.316 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 19.05 mm × 149316 N) / 1000 = 568.894 N·m (419.595 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

3/4"-16 UNF Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 3/4"-16 UNF
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 402.984 Nm
297.226 ft-lb
362.686 Nm
267.503 ft-lb
302.238 Nm
222.919 ft-lb
241.79 Nm
178.335 ft-lb
105.77 141.027
Grade 8 CURRENT 568.894 Nm
419.595 ft-lb
512.005 Nm
377.635 ft-lb
426.671 Nm
314.696 ft-lb
341.337 Nm
251.757 ft-lb
149.316 199.088
18-8 Stainless 213.353 Nm
157.361 ft-lb
192.017 Nm
141.625 ft-lb
160.014 Nm
118.021 ft-lb
128.012 Nm
94.416 ft-lb
55.998 74.664

Frequently Asked Engineering Questions (3/4"-16 UNF Grade 8)

What is the recommended tightening torque for a 3/4"-16 UNF Grade 8 bolt?
For a 3/4"-16 UNF SAE J429 Grade 8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 568.894 N·m (419.595 ft-lbs / 5035.14 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 426.671 N·m (314.696 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 341.337 N·m (251.757 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 3/4"-16 UNF internal threads?
The standard cut tap drill size for 3/4"-16 UNF is 11/16" (0.6875 in) (0.6875" / 17.462 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 18.191 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 3/4"-16 UNF Grade 8 fastener develop?
With a tensile stress area (As) of 240.619 mm² (0.37296 in²) and a nominal proof stress of 827.4 MPa (1,20,000 psi), a 3/4"-16 UNF Grade 8 fastener possesses an ultimate proof load of 199.088 kN (44,756.8 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 149.316 kN (33,567.6 lbf) across the joint interface.
What clearance hole diameters should be drilled for 3/4"-16 UNF bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 3/4"-16 UNF fastener are: Close Fit = 19.456 mm (0.766"), Normal Fit = 19.837 mm (0.781"), and Loose Fit = 20.65 mm (0.813"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.