Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

7/8"-9 UNC Grade 8 Torque & Tap Drill Spec

SAE J429 / ASTM A354 Grade BD

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
821.689 N·m
606.047 ft-lbs | 7272.56 in-lbs | 83.7889 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
184.857 kN
41,557.5 lbf
Target tension across joint interface
75% Tap Drill d - P
19.446 mm
49/64" (0.7656 in) (91% Eng.)
50% Hard Metal Drill: 20.698 mm
Direct Engineering Specification Summary

The recommended tightening torque for a 7/8"-9 UNC Grade 8 bolt is 821.689 N·m (606.047 ft-lbs) when dry (K=0.20) and 616.267 N·m (454.535 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 184.857 kN (41,557.5 lbf) at 75% proof load. Standard 75% tap drill is 49/64" (0.7656 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 22.225 mm (0.875") P = 2.82222 mm 7/8"-9 UNC Close: 22.631mm Normal: 23.012mm Loose: 23.825mm
Stress Area (As) 297.892 mm²
Pitch Diameter (d2) 20.392 mm
Minor Diameter (d1) 19.17 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (22.225 − 0.9382 × 2.82222)² = 297.892 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 297.892 mm² × 827.4 N/mm² = 246476 N (246.476 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 246476 N = 184857 N (184.857 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 22.225 mm × 184857 N) / 1000 = 821.689 N·m (606.047 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

7/8"-9 UNC Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: 7/8"-9 UNC
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 582.054 Nm
429.301 ft-lb
523.849 Nm
386.371 ft-lb
436.541 Nm
321.976 ft-lb
349.233 Nm
257.581 ft-lb
130.946 174.595
Grade 8 CURRENT 821.689 Nm
606.047 ft-lb
739.52 Nm
545.442 ft-lb
616.267 Nm
454.535 ft-lb
493.013 Nm
363.628 ft-lb
184.857 246.476
18-8 Stainless 308.158 Nm
227.286 ft-lb
277.342 Nm
204.557 ft-lb
231.119 Nm
170.464 ft-lb
184.895 Nm
136.371 ft-lb
69.327 92.436

Frequently Asked Engineering Questions (7/8"-9 UNC Grade 8)

What is the recommended tightening torque for a 7/8"-9 UNC Grade 8 bolt?
For a 7/8"-9 UNC SAE J429 Grade 8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 821.689 N·m (606.047 ft-lbs / 7272.56 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 616.267 N·m (454.535 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 493.013 N·m (363.628 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 7/8"-9 UNC internal threads?
The standard cut tap drill size for 7/8"-9 UNC is 49/64" (0.7656 in) (0.7656" / 19.446 mm), which delivers approximately 91% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 20.698 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 7/8"-9 UNC Grade 8 fastener develop?
With a tensile stress area (As) of 297.892 mm² (0.46173 in²) and a nominal proof stress of 827.4 MPa (1,20,000 psi), a 7/8"-9 UNC Grade 8 fastener possesses an ultimate proof load of 246.476 kN (55,410 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 184.857 kN (41,557.5 lbf) across the joint interface.
What clearance hole diameters should be drilled for 7/8"-9 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 7/8"-9 UNC fastener are: Close Fit = 22.631 mm (0.891"), Normal Fit = 23.012 mm (0.906"), and Loose Fit = 23.825 mm (0.938"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.