#6-32 UNC Grade 8 Torque & Tap Drill Spec
SAE J429 / ASTM A354 Grade BDLive Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
2.55 N·m
1.881 ft-lbs | 22.57 in-lbs | 0.26 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
3.637 kN
817.6 lbf
Target tension across joint interface
75% Tap Drill d - P
2.705 mm
#36 (0.1065 in) (93.1% Eng.)
50% Hard Metal Drill: 3.076 mm
Direct Engineering Specification Summary
The recommended tightening torque for a #6-32 UNC Grade 8 bolt is 2.55 N·m (1.881 ft-lbs) when dry (K=0.20) and 1.912 N·m (1.41 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 3.637 kN (817.6 lbf) at 75% proof load. Standard 75% tap drill is #36 (0.1065 in).
Thread & Hole Blueprint Visualizer
ASME B1.1 Unified Inch Screw Threads (60° UN) Stress Area (As) 5.861 mm²
Pitch Diameter (d2) 2.99 mm
Minor Diameter (d1) 2.646 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (3.5052 − 0.9382 × 0.79375)² = 5.861 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 5.861 mm² × 827.4 N/mm² = 4849 N (4.849 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 4849 N = 3637 N (3.637 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 3.5052 mm × 3637 N) / 1000 = 2.55 N·m (1.881 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
#6-32 UNC Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Grade 5 | 1.806 Nm 1.332 ft-lb | 1.626 Nm 1.199 ft-lb | 1.355 Nm 0.999 ft-lb | 1.084 Nm 0.799 ft-lb | 2.576 | 3.435 |
| Grade 8 CURRENT | 2.55 Nm 1.881 ft-lb | 2.295 Nm 1.693 ft-lb | 1.912 Nm 1.41 ft-lb | 1.53 Nm 1.128 ft-lb | 3.637 | 4.849 |
| 18-8 Stainless | 0.956 Nm 0.705 ft-lb | 0.861 Nm 0.635 ft-lb | 0.717 Nm 0.529 ft-lb | 0.574 Nm 0.423 ft-lb | 1.364 | 1.819 |
Frequently Asked Engineering Questions (#6-32 UNC Grade 8)
What is the recommended tightening torque for a #6-32 UNC Grade 8 bolt?
For a #6-32 UNC SAE J429 Grade 8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 2.55 N·m (1.881 ft-lbs / 22.57 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 1.912 N·m (1.41 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 1.53 N·m (1.128 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping #6-32 UNC internal threads?
The standard cut tap drill size for #6-32 UNC is #36 (0.1065 in) (0.1065" / 2.705 mm), which delivers approximately 93.1% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 3.076 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a #6-32 UNC Grade 8 fastener develop?
With a tensile stress area (As) of 5.861 mm² (0.00909 in²) and a nominal proof stress of 827.4 MPa (1,20,000 psi), a #6-32 UNC Grade 8 fastener possesses an ultimate proof load of 4.849 kN (1,090.2 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 3.637 kN (817.6 lbf) across the joint interface.
What clearance hole diameters should be drilled for #6-32 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a #6-32 UNC fastener are: Close Fit = 3.797 mm (0.1495"), Normal Fit = 4.216 mm (0.166"), and Loose Fit = 4.496 mm (0.177"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.