Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

#6-32 UNC 18-8 Stainless Torque & Tap Drill Spec

ASTM F593 Group 1 / AISI 304

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
0.956 N·m
0.705 ft-lbs | 8.46 in-lbs | 0.0975 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
1.364 kN
306.6 lbf
Target tension across joint interface
75% Tap Drill d - P
2.705 mm
#36 (0.1065 in) (93.1% Eng.)
50% Hard Metal Drill: 3.076 mm
Direct Engineering Specification Summary

The recommended tightening torque for a #6-32 UNC 18-8 Stainless bolt is 0.956 N·m (0.705 ft-lbs) when dry (K=0.20) and 0.717 N·m (0.529 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 1.364 kN (306.6 lbf) at 75% proof load. Standard 75% tap drill is #36 (0.1065 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 3.5052 mm (0.138") P = 0.79375 mm #6-32 UNC Close: 3.797mm Normal: 4.216mm Loose: 4.496mm
Stress Area (As) 5.861 mm²
Pitch Diameter (d2) 2.99 mm
Minor Diameter (d1) 2.646 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (3.5052 − 0.9382 × 0.79375)² = 5.861 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 5.861 mm² × 310.3 N/mm² = 1819 N (1.819 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 1819 N = 1364 N (1.364 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 3.5052 mm × 1364 N) / 1000 = 0.956 N·m (0.705 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

#6-32 UNC Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: #6-32 UNC
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 1.806 Nm
1.332 ft-lb
1.626 Nm
1.199 ft-lb
1.355 Nm
0.999 ft-lb
1.084 Nm
0.799 ft-lb
2.576 3.435
Grade 8 2.55 Nm
1.881 ft-lb
2.295 Nm
1.693 ft-lb
1.912 Nm
1.41 ft-lb
1.53 Nm
1.128 ft-lb
3.637 4.849
18-8 Stainless CURRENT 0.956 Nm
0.705 ft-lb
0.861 Nm
0.635 ft-lb
0.717 Nm
0.529 ft-lb
0.574 Nm
0.423 ft-lb
1.364 1.819

Frequently Asked Engineering Questions (#6-32 UNC 18-8 Stainless)

What is the recommended tightening torque for a #6-32 UNC 18-8 Stainless bolt?
For a #6-32 UNC 18-8 Stainless Steel (ASTM F593 Group 1) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 0.956 N·m (0.705 ft-lbs / 8.46 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 0.717 N·m (0.529 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 0.574 N·m (0.423 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping #6-32 UNC internal threads?
The standard cut tap drill size for #6-32 UNC is #36 (0.1065 in) (0.1065" / 2.705 mm), which delivers approximately 93.1% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 3.076 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a #6-32 UNC 18-8 Stainless fastener develop?
With a tensile stress area (As) of 5.861 mm² (0.00909 in²) and a nominal proof stress of 310.3 MPa (45,000 psi), a #6-32 UNC 18-8 Stainless fastener possesses an ultimate proof load of 1.819 kN (408.9 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 1.364 kN (306.6 lbf) across the joint interface.
What clearance hole diameters should be drilled for #6-32 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a #6-32 UNC fastener are: Close Fit = 3.797 mm (0.1495"), Normal Fit = 4.216 mm (0.166"), and Loose Fit = 4.496 mm (0.177"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.