7/8"-9 UNC Grade 5 Torque & Tap Drill Spec
SAE J429 / ASTM A449Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
582.054 N·m
429.301 ft-lbs | 5151.62 in-lbs | 59.353 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
130.946 kN
29,437.8 lbf
Target tension across joint interface
75% Tap Drill d - P
19.446 mm
49/64" (0.7656 in) (91% Eng.)
50% Hard Metal Drill: 20.698 mm
Direct Engineering Specification Summary
The recommended tightening torque for a 7/8"-9 UNC Grade 5 bolt is 582.054 N·m (429.301 ft-lbs) when dry (K=0.20) and 436.541 N·m (321.976 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 130.946 kN (29,437.8 lbf) at 75% proof load. Standard 75% tap drill is 49/64" (0.7656 in).
Thread & Hole Blueprint Visualizer
ASME B1.1 Unified Inch Screw Threads (60° UN) Stress Area (As) 297.892 mm²
Pitch Diameter (d2) 20.392 mm
Minor Diameter (d1) 19.17 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (22.225 − 0.9382 × 2.82222)² = 297.892 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 297.892 mm² × 586.1 N/mm² = 174595 N (174.595 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 174595 N = 130946 N (130.946 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 22.225 mm × 130946 N) / 1000 = 582.054 N·m (429.301 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
7/8"-9 UNC Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Grade 5 CURRENT | 582.054 Nm 429.301 ft-lb | 523.849 Nm 386.371 ft-lb | 436.541 Nm 321.976 ft-lb | 349.233 Nm 257.581 ft-lb | 130.946 | 174.595 |
| Grade 8 | 821.689 Nm 606.047 ft-lb | 739.52 Nm 545.442 ft-lb | 616.267 Nm 454.535 ft-lb | 493.013 Nm 363.628 ft-lb | 184.857 | 246.476 |
| 18-8 Stainless | 308.158 Nm 227.286 ft-lb | 277.342 Nm 204.557 ft-lb | 231.119 Nm 170.464 ft-lb | 184.895 Nm 136.371 ft-lb | 69.327 | 92.436 |
Frequently Asked Engineering Questions (7/8"-9 UNC Grade 5)
What is the recommended tightening torque for a 7/8"-9 UNC Grade 5 bolt?
For a 7/8"-9 UNC SAE J429 Grade 5 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 582.054 N·m (429.301 ft-lbs / 5151.62 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 436.541 N·m (321.976 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 349.233 N·m (257.581 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping 7/8"-9 UNC internal threads?
The standard cut tap drill size for 7/8"-9 UNC is 49/64" (0.7656 in) (0.7656" / 19.446 mm), which delivers approximately 91% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 20.698 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a 7/8"-9 UNC Grade 5 fastener develop?
With a tensile stress area (As) of 297.892 mm² (0.46173 in²) and a nominal proof stress of 586.1 MPa (85,000 psi), a 7/8"-9 UNC Grade 5 fastener possesses an ultimate proof load of 174.595 kN (39,250.4 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 130.946 kN (29,437.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for 7/8"-9 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a 7/8"-9 UNC fastener are: Close Fit = 22.631 mm (0.891"), Normal Fit = 23.012 mm (0.906"), and Loose Fit = 23.825 mm (0.938"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.