M22 x 2.5 A2-70 Stainless Torque & Tap Drill Spec
ISO 3506-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
450.548 N·m
332.307 ft-lbs | 3987.68 in-lbs | 45.9431 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
102.397 kN
23,019.8 lbf
Target tension across joint interface
75% Tap Drill d - P
19.5 mm
19.5 mm (92.4% Eng.)
50% Hard Metal Drill: 20.647 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M22 x 2.5 A2-70 Stainless bolt is 450.548 N·m (332.307 ft-lbs) when dry (K=0.20) and 337.911 N·m (249.23 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 102.397 kN (23,019.8 lbf) at 75% proof load. Standard 75% tap drill is 19.5 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 303.399 mm²
Pitch Diameter (d2) 20.376 mm
Minor Diameter (d1) 19.294 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (22 − 0.9382 × 2.5)² = 303.399 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 303.399 mm² × 450 N/mm² = 136530 N (136.53 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 136530 N = 102397 N (102.397 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 22 mm × 102397 N) / 1000 = 450.548 N·m (332.307 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M22 x 2.5 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 600.73 Nm 443.076 ft-lb | 540.657 Nm 398.768 ft-lb | 450.548 Nm 332.307 ft-lb | 360.438 Nm 265.845 ft-lb | 136.53 | 182.039 |
| Class 10.9 | 831.01 Nm 612.921 ft-lb | 747.909 Nm 551.629 ft-lb | 623.257 Nm 459.691 ft-lb | 498.606 Nm 367.753 ft-lb | 188.866 | 251.821 |
| Class 12.9 | 971.18 Nm 716.306 ft-lb | 874.062 Nm 644.675 ft-lb | 728.385 Nm 537.229 ft-lb | 582.708 Nm 429.783 ft-lb | 220.723 | 294.297 |
| A2-70 Stainless CURRENT | 450.548 Nm 332.307 ft-lb | 405.493 Nm 299.076 ft-lb | 337.911 Nm 249.23 ft-lb | 270.329 Nm 199.384 ft-lb | 102.397 | 136.53 |
| A4-80 Marine Stainless | 600.73 Nm 443.076 ft-lb | 540.657 Nm 398.768 ft-lb | 450.548 Nm 332.307 ft-lb | 360.438 Nm 265.845 ft-lb | 136.53 | 182.039 |
Frequently Asked Engineering Questions (M22 x 2.5 A2-70 Stainless)
What is the recommended tightening torque for a M22 x 2.5 A2-70 Stainless bolt?
For a M22 x 2.5 Stainless Steel A2-70 (AISI 304 / EN 1.4301) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 450.548 N·m (332.307 ft-lbs / 3987.68 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 337.911 N·m (249.23 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 270.329 N·m (199.384 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M22 x 2.5 internal threads?
The standard cut tap drill size for M22 x 2.5 is 19.5 mm (0.7677" / 19.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 20.647 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M22 x 2.5 A2-70 Stainless fastener develop?
With a tensile stress area (As) of 303.399 mm² (0.47027 in²) and a nominal proof stress of 450 MPa (65,267 psi), a M22 x 2.5 A2-70 Stainless fastener possesses an ultimate proof load of 136.53 kN (30,693.1 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 102.397 kN (23,019.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for M22 x 2.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M22 x 2.5 fastener are: Close Fit = 23 mm (0.9055"), Normal Fit = 24 mm (0.9449"), and Loose Fit = 26 mm (1.0236"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.