Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M22 x 2.5 Class 8.8 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
600.73 N·m
443.076 ft-lbs | 5316.91 in-lbs | 61.2574 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
136.53 kN
30,693.1 lbf
Target tension across joint interface
75% Tap Drill d - P
19.5 mm
19.5 mm (92.4% Eng.)
50% Hard Metal Drill: 20.647 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M22 x 2.5 Class 8.8 bolt is 600.73 N·m (443.076 ft-lbs) when dry (K=0.20) and 450.548 N·m (332.307 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 136.53 kN (30,693.1 lbf) at 75% proof load. Standard 75% tap drill is 19.5 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 22 mm (0.8661") P = 2.5 mm M22 x 2.5 Close: 23mm Normal: 24mm Loose: 26mm
Stress Area (As) 303.399 mm²
Pitch Diameter (d2) 20.376 mm
Minor Diameter (d1) 19.294 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (22 − 0.9382 × 2.5)² = 303.399 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 303.399 mm² × 600 N/mm² = 182039 N (182.039 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 182039 N = 136530 N (136.53 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 22 mm × 136530 N) / 1000 = 600.73 N·m (443.076 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M22 x 2.5 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M22 x 2.5
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 CURRENT 600.73 Nm
443.076 ft-lb
540.657 Nm
398.768 ft-lb
450.548 Nm
332.307 ft-lb
360.438 Nm
265.845 ft-lb
136.53 182.039
Class 10.9 831.01 Nm
612.921 ft-lb
747.909 Nm
551.629 ft-lb
623.257 Nm
459.691 ft-lb
498.606 Nm
367.753 ft-lb
188.866 251.821
Class 12.9 971.18 Nm
716.306 ft-lb
874.062 Nm
644.675 ft-lb
728.385 Nm
537.229 ft-lb
582.708 Nm
429.783 ft-lb
220.723 294.297
A2-70 Stainless 450.548 Nm
332.307 ft-lb
405.493 Nm
299.076 ft-lb
337.911 Nm
249.23 ft-lb
270.329 Nm
199.384 ft-lb
102.397 136.53
A4-80 Marine Stainless 600.73 Nm
443.076 ft-lb
540.657 Nm
398.768 ft-lb
450.548 Nm
332.307 ft-lb
360.438 Nm
265.845 ft-lb
136.53 182.039

Frequently Asked Engineering Questions (M22 x 2.5 Class 8.8)

What is the recommended tightening torque for a M22 x 2.5 Class 8.8 bolt?
For a M22 x 2.5 ISO Metric Property Class 8.8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 600.73 N·m (443.076 ft-lbs / 5316.91 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 450.548 N·m (332.307 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 360.438 N·m (265.845 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M22 x 2.5 internal threads?
The standard cut tap drill size for M22 x 2.5 is 19.5 mm (0.7677" / 19.5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 20.647 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M22 x 2.5 Class 8.8 fastener develop?
With a tensile stress area (As) of 303.399 mm² (0.47027 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M22 x 2.5 Class 8.8 fastener possesses an ultimate proof load of 182.039 kN (40,924.1 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 136.53 kN (30,693.1 lbf) across the joint interface.
What clearance hole diameters should be drilled for M22 x 2.5 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M22 x 2.5 fastener are: Close Fit = 23 mm (0.9055"), Normal Fit = 24 mm (0.9449"), and Loose Fit = 26 mm (1.0236"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.