Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M4 x 0.7 Class 8.8 Torque & Tap Drill Spec

ISO 898-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
3.16 N·m
2.331 ft-lbs | 27.97 in-lbs | 0.3223 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
3.951 kN
888.1 lbf
Target tension across joint interface
75% Tap Drill d - P
3.3 mm
3.3 mm (92.4% Eng.)
50% Hard Metal Drill: 3.621 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M4 x 0.7 Class 8.8 bolt is 3.16 N·m (2.331 ft-lbs) when dry (K=0.20) and 2.37 N·m (1.748 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 3.951 kN (888.1 lbf) at 75% proof load. Standard 75% tap drill is 3.3 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 4 mm (0.1575") P = 0.7 mm M4 x 0.7 Close: 4.3mm Normal: 4.5mm Loose: 4.8mm
Stress Area (As) 8.779 mm²
Pitch Diameter (d2) 3.545 mm
Minor Diameter (d1) 3.242 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (4 − 0.9382 × 0.7)² = 8.779 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 8.779 mm² × 600 N/mm² = 5267 N (5.267 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 5267 N = 3951 N (3.951 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 4 mm × 3951 N) / 1000 = 3.16 N·m (2.331 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M4 x 0.7 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M4 x 0.7
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 CURRENT 3.16 Nm
2.331 ft-lb
2.844 Nm
2.098 ft-lb
2.37 Nm
1.748 ft-lb
1.896 Nm
1.399 ft-lb
3.951 5.267
Class 10.9 4.372 Nm
3.225 ft-lb
3.935 Nm
2.902 ft-lb
3.279 Nm
2.418 ft-lb
2.623 Nm
1.935 ft-lb
5.465 7.287
Class 12.9 5.109 Nm
3.768 ft-lb
4.598 Nm
3.392 ft-lb
3.832 Nm
2.826 ft-lb
3.066 Nm
2.261 ft-lb
6.387 8.516
A2-70 Stainless 2.37 Nm
1.748 ft-lb
2.133 Nm
1.573 ft-lb
1.778 Nm
1.311 ft-lb
1.422 Nm
1.049 ft-lb
2.963 3.951
A4-80 Marine Stainless 3.16 Nm
2.331 ft-lb
2.844 Nm
2.098 ft-lb
2.37 Nm
1.748 ft-lb
1.896 Nm
1.399 ft-lb
3.951 5.267

Frequently Asked Engineering Questions (M4 x 0.7 Class 8.8)

What is the recommended tightening torque for a M4 x 0.7 Class 8.8 bolt?
For a M4 x 0.7 ISO Metric Property Class 8.8 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 3.16 N·m (2.331 ft-lbs / 27.97 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 2.37 N·m (1.748 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 1.896 N·m (1.399 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M4 x 0.7 internal threads?
The standard cut tap drill size for M4 x 0.7 is 3.3 mm (0.1299" / 3.3 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 3.621 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M4 x 0.7 Class 8.8 fastener develop?
With a tensile stress area (As) of 8.779 mm² (0.01361 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M4 x 0.7 Class 8.8 fastener possesses an ultimate proof load of 5.267 kN (1,184.2 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 3.951 kN (888.1 lbf) across the joint interface.
What clearance hole diameters should be drilled for M4 x 0.7 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M4 x 0.7 fastener are: Close Fit = 4.3 mm (0.1693"), Normal Fit = 4.5 mm (0.1772"), and Loose Fit = 4.8 mm (0.189"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.