M4 x 0.7 Class 12.9 Torque & Tap Drill Spec
ISO 898-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
5.109 N·m
3.768 ft-lbs | 45.22 in-lbs | 0.521 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
6.387 kN
1,435.8 lbf
Target tension across joint interface
75% Tap Drill d - P
3.3 mm
3.3 mm (92.4% Eng.)
50% Hard Metal Drill: 3.621 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M4 x 0.7 Class 12.9 bolt is 5.109 N·m (3.768 ft-lbs) when dry (K=0.20) and 3.832 N·m (2.826 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 6.387 kN (1,435.8 lbf) at 75% proof load. Standard 75% tap drill is 3.3 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 8.779 mm²
Pitch Diameter (d2) 3.545 mm
Minor Diameter (d1) 3.242 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (4 − 0.9382 × 0.7)² = 8.779 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 8.779 mm² × 970 N/mm² = 8516 N (8.516 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 8516 N = 6387 N (6.387 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 4 mm × 6387 N) / 1000 = 5.109 N·m (3.768 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M4 x 0.7 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 3.16 Nm 2.331 ft-lb | 2.844 Nm 2.098 ft-lb | 2.37 Nm 1.748 ft-lb | 1.896 Nm 1.399 ft-lb | 3.951 | 5.267 |
| Class 10.9 | 4.372 Nm 3.225 ft-lb | 3.935 Nm 2.902 ft-lb | 3.279 Nm 2.418 ft-lb | 2.623 Nm 1.935 ft-lb | 5.465 | 7.287 |
| Class 12.9 CURRENT | 5.109 Nm 3.768 ft-lb | 4.598 Nm 3.392 ft-lb | 3.832 Nm 2.826 ft-lb | 3.066 Nm 2.261 ft-lb | 6.387 | 8.516 |
| A2-70 Stainless | 2.37 Nm 1.748 ft-lb | 2.133 Nm 1.573 ft-lb | 1.778 Nm 1.311 ft-lb | 1.422 Nm 1.049 ft-lb | 2.963 | 3.951 |
| A4-80 Marine Stainless | 3.16 Nm 2.331 ft-lb | 2.844 Nm 2.098 ft-lb | 2.37 Nm 1.748 ft-lb | 1.896 Nm 1.399 ft-lb | 3.951 | 5.267 |
Frequently Asked Engineering Questions (M4 x 0.7 Class 12.9)
What is the recommended tightening torque for a M4 x 0.7 Class 12.9 bolt?
For a M4 x 0.7 ISO Metric Property Class 12.9 bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 5.109 N·m (3.768 ft-lbs / 45.22 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 3.832 N·m (2.826 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 3.066 N·m (2.261 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M4 x 0.7 internal threads?
The standard cut tap drill size for M4 x 0.7 is 3.3 mm (0.1299" / 3.3 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 3.621 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M4 x 0.7 Class 12.9 fastener develop?
With a tensile stress area (As) of 8.779 mm² (0.01361 in²) and a nominal proof stress of 970 MPa (1,40,687 psi), a M4 x 0.7 Class 12.9 fastener possesses an ultimate proof load of 8.516 kN (1,914.4 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 6.387 kN (1,435.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for M4 x 0.7 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M4 x 0.7 fastener are: Close Fit = 4.3 mm (0.1693"), Normal Fit = 4.5 mm (0.1772"), and Loose Fit = 4.8 mm (0.189"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.