Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M5 x 0.8 A4-80 Marine Stainless Torque & Tap Drill Spec

ISO 3506-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
6.382 N·m
4.707 ft-lbs | 56.49 in-lbs | 0.6508 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
6.382 kN
1,434.8 lbf
Target tension across joint interface
75% Tap Drill d - P
4.2 mm
4.2 mm (92.4% Eng.)
50% Hard Metal Drill: 4.567 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M5 x 0.8 A4-80 Marine Stainless bolt is 6.382 N·m (4.707 ft-lbs) when dry (K=0.20) and 4.787 N·m (3.531 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 6.382 kN (1,434.8 lbf) at 75% proof load. Standard 75% tap drill is 4.2 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 5 mm (0.1969") P = 0.8 mm M5 x 0.8 Close: 5.3mm Normal: 5.5mm Loose: 5.8mm
Stress Area (As) 14.183 mm²
Pitch Diameter (d2) 4.48 mm
Minor Diameter (d1) 4.134 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (5 − 0.9382 × 0.8)² = 14.183 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 14.183 mm² × 600 N/mm² = 8510 N (8.51 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 8510 N = 6382 N (6.382 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 5 mm × 6382 N) / 1000 = 6.382 N·m (4.707 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M5 x 0.8 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M5 x 0.8
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 6.382 Nm
4.707 ft-lb
5.744 Nm
4.237 ft-lb
4.787 Nm
3.531 ft-lb
3.829 Nm
2.824 ft-lb
6.382 8.51
Class 10.9 8.829 Nm
6.512 ft-lb
7.946 Nm
5.861 ft-lb
6.622 Nm
4.884 ft-lb
5.297 Nm
3.907 ft-lb
8.829 11.772
Class 12.9 10.318 Nm
7.61 ft-lb
9.286 Nm
6.849 ft-lb
7.739 Nm
5.708 ft-lb
6.191 Nm
4.566 ft-lb
10.318 13.758
A2-70 Stainless 4.787 Nm
3.531 ft-lb
4.308 Nm
3.177 ft-lb
3.59 Nm
2.648 ft-lb
2.872 Nm
2.118 ft-lb
4.787 6.382
A4-80 Marine Stainless CURRENT 6.382 Nm
4.707 ft-lb
5.744 Nm
4.237 ft-lb
4.787 Nm
3.531 ft-lb
3.829 Nm
2.824 ft-lb
6.382 8.51

Frequently Asked Engineering Questions (M5 x 0.8 A4-80 Marine Stainless)

What is the recommended tightening torque for a M5 x 0.8 A4-80 Marine Stainless bolt?
For a M5 x 0.8 Stainless Steel A4-80 (AISI 316 / Marine Grade / EN 1.4401) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 6.382 N·m (4.707 ft-lbs / 56.49 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 4.787 N·m (3.531 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 3.829 N·m (2.824 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M5 x 0.8 internal threads?
The standard cut tap drill size for M5 x 0.8 is 4.2 mm (0.1654" / 4.2 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 4.567 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M5 x 0.8 A4-80 Marine Stainless fastener develop?
With a tensile stress area (As) of 14.183 mm² (0.02198 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M5 x 0.8 A4-80 Marine Stainless fastener possesses an ultimate proof load of 8.51 kN (1,913.1 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 6.382 kN (1,434.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for M5 x 0.8 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M5 x 0.8 fastener are: Close Fit = 5.3 mm (0.2087"), Normal Fit = 5.5 mm (0.2165"), and Loose Fit = 5.8 mm (0.2283"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.