Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

M6 x 1.0 A4-80 Marine Stainless Torque & Tap Drill Spec

ISO 3506-1

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
10.866 N·m
8.015 ft-lbs | 96.18 in-lbs | 1.1081 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
9.055 kN
2,035.7 lbf
Target tension across joint interface
75% Tap Drill d - P
5 mm
5.0 mm (92.4% Eng.)
50% Hard Metal Drill: 5.459 mm
Direct Engineering Specification Summary

The recommended tightening torque for a M6 x 1.0 A4-80 Marine Stainless bolt is 10.866 N·m (8.015 ft-lbs) when dry (K=0.20) and 8.15 N·m (6.011 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 9.055 kN (2,035.7 lbf) at 75% proof load. Standard 75% tap drill is 5.0 mm.

Thread & Hole Blueprint Visualizer

ISO 261 / ISO 965-1 (Metric 60°)
d = 6 mm (0.2362") P = 1 mm M6 x 1.0 Close: 6.4mm Normal: 6.6mm Loose: 7mm
Stress Area (As) 20.123 mm²
Pitch Diameter (d2) 5.35 mm
Minor Diameter (d1) 4.917 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (6 − 0.9382 × 1)² = 20.123 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 20.123 mm² × 600 N/mm² = 12074 N (12.074 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 12074 N = 9055 N (9.055 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 6 mm × 9055 N) / 1000 = 10.866 N·m (8.015 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

M6 x 1.0 Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: M6 x 1.0
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Class 8.8 10.866 Nm
8.015 ft-lb
9.78 Nm
7.213 ft-lb
8.15 Nm
6.011 ft-lb
6.52 Nm
4.809 ft-lb
9.055 12.074
Class 10.9 15.032 Nm
11.087 ft-lb
13.529 Nm
9.978 ft-lb
11.274 Nm
8.315 ft-lb
9.019 Nm
6.652 ft-lb
12.527 16.702
Class 12.9 17.567 Nm
12.957 ft-lb
15.811 Nm
11.661 ft-lb
13.176 Nm
9.718 ft-lb
10.54 Nm
7.774 ft-lb
14.639 19.519
A2-70 Stainless 8.15 Nm
6.011 ft-lb
7.335 Nm
5.41 ft-lb
6.112 Nm
4.508 ft-lb
4.89 Nm
3.607 ft-lb
6.792 9.055
A4-80 Marine Stainless CURRENT 10.866 Nm
8.015 ft-lb
9.78 Nm
7.213 ft-lb
8.15 Nm
6.011 ft-lb
6.52 Nm
4.809 ft-lb
9.055 12.074

Frequently Asked Engineering Questions (M6 x 1.0 A4-80 Marine Stainless)

What is the recommended tightening torque for a M6 x 1.0 A4-80 Marine Stainless bolt?
For a M6 x 1.0 Stainless Steel A4-80 (AISI 316 / Marine Grade / EN 1.4401) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 10.866 N·m (8.015 ft-lbs / 96.18 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 8.15 N·m (6.011 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 6.52 N·m (4.809 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M6 x 1.0 internal threads?
The standard cut tap drill size for M6 x 1.0 is 5.0 mm (0.1969" / 5 mm), which delivers approximately 92.4% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 5.459 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M6 x 1.0 A4-80 Marine Stainless fastener develop?
With a tensile stress area (As) of 20.123 mm² (0.03119 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M6 x 1.0 A4-80 Marine Stainless fastener possesses an ultimate proof load of 12.074 kN (2,714.3 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 9.055 kN (2,035.7 lbf) across the joint interface.
What clearance hole diameters should be drilled for M6 x 1.0 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M6 x 1.0 fastener are: Close Fit = 6.4 mm (0.252"), Normal Fit = 6.6 mm (0.2598"), and Loose Fit = 7 mm (0.2756"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.