M8 x 1.25 A4-80 Marine Stainless Torque & Tap Drill Spec
ISO 3506-1Live Joint Clamp & Torque Engine
K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
26.358 N·m
19.44 ft-lbs | 233.29 in-lbs | 2.6877 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
16.474 kN
3,703.4 lbf
Target tension across joint interface
75% Tap Drill d - P
6.8 mm
6.8 mm (88.7% Eng.)
50% Hard Metal Drill: 7.323 mm
Direct Engineering Specification Summary
The recommended tightening torque for a M8 x 1.25 A4-80 Marine Stainless bolt is 26.358 N·m (19.44 ft-lbs) when dry (K=0.20) and 19.768 N·m (14.58 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 16.474 kN (3,703.4 lbf) at 75% proof load. Standard 75% tap drill is 6.8 mm.
Thread & Hole Blueprint Visualizer
ISO 261 / ISO 965-1 (Metric 60°) Stress Area (As) 36.608 mm²
Pitch Diameter (d2) 7.188 mm
Minor Diameter (d1) 6.647 mm
Step-by-Step Mathematical Derivation
VDI 2230 / ISO 898-1Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (8 − 0.9382 × 1.25)² = 36.608 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 36.608 mm² × 600 N/mm² = 21965 N (21.965 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 21965 N = 16474 N (16.474 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 8 mm × 16474 N) / 1000 = 26.358 N·m (19.44 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.
M8 x 1.25 Torque Across All Grades & Friction Conditions
Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.
| Grade / Class | Dry (K=0.20) | Zinc (K=0.18) | Oil (K=0.15) | Moly (K=0.12) | Clamp (kN) | Proof (kN) |
|---|---|---|---|---|---|---|
| Class 8.8 | 26.358 Nm 19.44 ft-lb | 23.722 Nm 17.496 ft-lb | 19.768 Nm 14.58 ft-lb | 15.815 Nm 11.664 ft-lb | 16.474 | 21.965 |
| Class 10.9 | 36.462 Nm 26.893 ft-lb | 32.815 Nm 24.203 ft-lb | 27.346 Nm 20.17 ft-lb | 21.877 Nm 16.136 ft-lb | 22.788 | 30.385 |
| Class 12.9 | 42.612 Nm 31.429 ft-lb | 38.351 Nm 28.286 ft-lb | 31.959 Nm 23.572 ft-lb | 25.567 Nm 18.857 ft-lb | 26.632 | 35.51 |
| A2-70 Stainless | 19.768 Nm 14.58 ft-lb | 17.791 Nm 13.122 ft-lb | 14.826 Nm 10.935 ft-lb | 11.861 Nm 8.748 ft-lb | 12.355 | 16.474 |
| A4-80 Marine Stainless CURRENT | 26.358 Nm 19.44 ft-lb | 23.722 Nm 17.496 ft-lb | 19.768 Nm 14.58 ft-lb | 15.815 Nm 11.664 ft-lb | 16.474 | 21.965 |
Frequently Asked Engineering Questions (M8 x 1.25 A4-80 Marine Stainless)
What is the recommended tightening torque for a M8 x 1.25 A4-80 Marine Stainless bolt?
For a M8 x 1.25 Stainless Steel A4-80 (AISI 316 / Marine Grade / EN 1.4401) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 26.358 N·m (19.44 ft-lbs / 233.29 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 19.768 N·m (14.58 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 15.815 N·m (11.664 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping M8 x 1.25 internal threads?
The standard cut tap drill size for M8 x 1.25 is 6.8 mm (0.2677" / 6.8 mm), which delivers approximately 88.7% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 7.323 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a M8 x 1.25 A4-80 Marine Stainless fastener develop?
With a tensile stress area (As) of 36.608 mm² (0.05674 in²) and a nominal proof stress of 600 MPa (87,023 psi), a M8 x 1.25 A4-80 Marine Stainless fastener possesses an ultimate proof load of 21.965 kN (4,937.9 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 16.474 kN (3,703.4 lbf) across the joint interface.
What clearance hole diameters should be drilled for M8 x 1.25 bolts?
Per ISO 273 (Bolts & Screws Clearance Holes), recommended clearance hole diameters for a M8 x 1.25 fastener are: Close Fit = 8.4 mm (0.3307"), Normal Fit = 9 mm (0.3543"), and Loose Fit = 10 mm (0.3937"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.
Recent Calculations
No recent calculations saved yet.