Delrin (Acetal / Polyoxymethylene / POM-C) — 3/4" (0.750 in) 3-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 3/4" (0.750 in) 3-flute TiAlN carbide end mill, the recommended spindle speed is 8,355 RPM at 500 m/min (1640.4 SFM), with a profiling feed rate of 2,599 mm/min (102.3 IPM) and adjusted chip load of 0.1037 mm/tooth, achieving a material removal rate of 353.57 cm³/min (21.57 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathDelrin (Acetal / Polyoxymethylene / POM-C) (3/4" (0.750 in)) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 19.05 mm | 9.53 mm | 1× | 1,126 | 44.3 | 204.42 | 1.06 |
| Slotting (100% WOC) | 3F | 19.05 mm | 9.53 mm | 1× | 1,689 | 66.4 | 306.63 | 1.6 |
| Slotting (100% WOC) | 4F | 19.05 mm | 9.53 mm | 1× | 2,253 | 88.6 | 409.02 | 2.13 |
| Profiling / HEM (25% WOC) | 2F | 4.76 mm | 28.58 mm | 1.1549× | 1,733 | 68.2 | 235.76 | 1.23 |
| Profiling / HEM (25% WOC) CURRENT | 3F | 4.76 mm | 28.58 mm | 1.1549× | 2,599 | 102.3 | 353.57 | 1.84 |
| Profiling / HEM (25% WOC) | 4F | 4.76 mm | 28.58 mm | 1.1549× | 3,466 | 136.4 | 471.52 | 2.46 |
| Adaptive Clearing (10% WOC) | 2F | 1.91 mm | 38.1 mm | 1.6647× | 2,498 | 98.4 | 181.78 | 0.95 |
| Adaptive Clearing (10% WOC) | 3F | 1.91 mm | 38.1 mm | 1.6647× | 3,747 | 147.6 | 272.67 | 1.42 |
| Adaptive Clearing (10% WOC) | 4F | 1.91 mm | 38.1 mm | 1.6647× | 4,996 | 196.8 | 363.56 | 1.89 |
Shop-Floor Machining Strategy for Delrin (Acetal / Polyoxymethylene / POM-C)
Work Hardening: None (Stress relaxation can occur; stress-relieve stock for tight tolerances)Cold Air Gun (Vortex Tube) or Light Water-Soluble Flood Coolant
Pressure: Air gun at 5 bar
Avoid chlorinated or ester coolants that degrade polymers. Continuous chip evacuation prevents localized plastic remelting.
Chip Flow: Continuous plastic ribbons; high volume air evacuation required to prevent chip wrapping on spindle arbor.
Milling Direction: Climb milling produces pristine finishes.
- High chip load is essential: chips carry away the heat. If feed is too slow, plastic melts and binds to flutes.
- Use 1-flute (O-flute) or 2-flute upward spiral router/end mills for maximum chip clearance.
- Avoid over-clamping in vises; Delrin flexes easily under clamping jaw pressure.
Frequently Asked CNC Questions (Delrin (Acetal / Polyoxymethylene / POM-C) / 3/4" (0.750 in))
What is the recommended RPM for milling Delrin (Acetal / Polyoxymethylene / POM-C) with a 3/4" (0.750 in) end mill?
What table feed rate and chip load should I program for 3/4" (0.750 in) in Delrin (Acetal / Polyoxymethylene / POM-C)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Delrin (Acetal / Polyoxymethylene / POM-C)?
Recent Calculations
No recent calculations saved yet.