Polycarbonate (Lexan / PC Thermoplastic) — 3 mm 4-Flute Speeds & Feeds
Live CNC Milling Parameter Engine
For milling Polycarbonate (Lexan / PC Thermoplastic) with a 3 mm 4-flute TiAlN carbide end mill, the recommended spindle speed is 40,319 RPM at 380 m/min (1246.7 SFM), with a profiling feed rate of 3,371 mm/min (132.2 IPM) and adjusted chip load of 0.0209 mm/tooth, achieving a material removal rate of 11.38 cm³/min (0.69 in³/min).
Radial Engagement & Chip Thinning Blueprint
DIN 6584 / SandvikStep-by-Step Machining Physics Proof
DIN 6584 Cutting MathPolycarbonate (Lexan / PC Thermoplastic) (3 mm) Cutting Strategy Matrix
Pre-computed Speeds & Feeds across Slotting (100% ae), Profiling (25% ae), and Adaptive/HEM (10% ae).
| Operation Strategy | Flutes | Stepover (ae) | Depth (ap) | CTF | Feed (mm/min) | Feed (IPM) | MRR (cm³/min) | Power (kW) |
|---|---|---|---|---|---|---|---|---|
| Slotting (100% WOC) | 2F | 3 mm | 1.5 mm | 1× | 1,089 | 42.7 | 4.9 | 0.03 |
| Slotting (100% WOC) | 3F | 3 mm | 1.5 mm | 1× | 1,633 | 64.1 | 7.35 | 0.05 |
| Slotting (100% WOC) | 4F | 3 mm | 1.5 mm | 1× | 2,177 | 85.5 | 9.8 | 0.06 |
| Profiling / HEM (25% WOC) | 2F | 0.75 mm | 4.5 mm | 1.1547× | 1,685 | 66.1 | 5.69 | 0.04 |
| Profiling / HEM (25% WOC) | 3F | 0.75 mm | 4.5 mm | 1.1547× | 2,528 | 99.2 | 8.53 | 0.05 |
| Profiling / HEM (25% WOC) CURRENT | 4F | 0.75 mm | 4.5 mm | 1.1547× | 3,371 | 132.2 | 11.38 | 0.07 |
| Adaptive Clearing (10% WOC) | 2F | 0.3 mm | 6 mm | 1.6667× | 2,435 | 96 | 4.38 | 0.03 |
| Adaptive Clearing (10% WOC) | 3F | 0.3 mm | 6 mm | 1.6667× | 3,653 | 143.9 | 6.58 | 0.04 |
| Adaptive Clearing (10% WOC) | 4F | 0.3 mm | 6 mm | 1.6667× | 4,871 | 191.9 | 8.77 | 0.05 |
Shop-Floor Machining Strategy for Polycarbonate (Lexan / PC Thermoplastic)
Work Hardening: None (High internal residual stress from extrusion)Cold Air Blast Only or Pure Deionized Water
Pressure: Cold air gun at 5 bar
CRITICAL: Never expose polycarbonate to petroleum, synthetic cutting oils, or chemical solvents. Chemical exposure induces immediate catastrophic stress crazing and micro-fractures.
Chip Flow: Clean crisp plastic chips; air blast prevents chip recutting on optical surfaces.
Milling Direction: Climb milling mandatory to avoid chipping edge breakout.
- Maintain sharp high-rake tools; dull tools induce severe internal residual stress that causes delayed part cracking.
- Anneal machined parts at 120°C (250°F) for 2 hours if maximum impact strength is required.
- Use protective masking film on sheet surfaces to prevent surface scratches from chip wash.
Frequently Asked CNC Questions (Polycarbonate (Lexan / PC Thermoplastic) / 3 mm)
What is the recommended RPM for milling Polycarbonate (Lexan / PC Thermoplastic) with a 3 mm end mill?
What table feed rate and chip load should I program for 3 mm in Polycarbonate (Lexan / PC Thermoplastic)?
Why does radial chip thinning occur when milling at less than 50% stepover?
What coolant strategy is recommended for CNC machining Polycarbonate (Lexan / PC Thermoplastic)?
Recent Calculations
No recent calculations saved yet.