Skip to calculator
⚙️
TorqueAndFeed TorqueAndFeed.com • B2B Reference

#10-24 UNC 18-8 Stainless Torque & Tap Drill Spec

ASTM F593 Group 1 / AISI 304

Live Joint Clamp & Torque Engine

K = 0.20
75% Sp
Lubrication Condition Presets:
Recommended Tightening Torque T = K·d·Fi
2.541 N·m
1.874 ft-lbs | 22.49 in-lbs | 0.2591 kgf·m
Calibrated for Dry / Bare Steel conditions.
Clamp Preload Fi
2.632 kN
591.8 lbf
Target tension across joint interface
75% Tap Drill d - P
3.797 mm
#25 (0.1495 in) (89.8% Eng.)
50% Hard Metal Drill: 4.252 mm
Direct Engineering Specification Summary

The recommended tightening torque for a #10-24 UNC 18-8 Stainless bolt is 2.541 N·m (1.874 ft-lbs) when dry (K=0.20) and 1.906 N·m (1.405 ft-lbs) when lubricated (K=0.15), generating a clamp preload of 2.632 kN (591.8 lbf) at 75% proof load. Standard 75% tap drill is #25 (0.1495 in).

Thread & Hole Blueprint Visualizer

ASME B1.1 Unified Inch Screw Threads (60° UN)
d = 4.826 mm (0.19") P = 1.05833 mm #10-24 UNC Close: 5.182mm Normal: 5.613mm Loose: 5.944mm
Stress Area (As) 11.311 mm²
Pitch Diameter (d2) 4.139 mm
Minor Diameter (d1) 3.68 mm

Step-by-Step Mathematical Derivation

VDI 2230 / ISO 898-1
Step 1: Tensile Stress Area (As)
As = (π / 4) × (d − 0.9382 × P)²
As = (π / 4) × (4.826 − 0.9382 × 1.05833)² = 11.311 mm²
Step 2: Proof Load (Fp)
Fp = As × Sp
Fp = 11.311 mm² × 310.3 N/mm² = 3510 N (3.51 kN)
Step 3: Target Clamp Preload (Fi @ 75% Proof)
Fi = 0.75 × Fp
Fi = 0.75 × 3510 N = 2632 N (2.632 kN)
Step 4: Tightening Torque (Dry K=0.20)
T = (K × d × Fi) / 1000
T = (0.20 × 4.826 mm × 2632 N) / 1000 = 2.541 N·m (1.874 ft-lbs)
Formula verified per ISO 898-1 and Machinery's Handbook 31st Edition. Assumes unhardened flat washer under head.

#10-24 UNC Torque Across All Grades & Friction Conditions

Comparison matrix calculated at 75% proof stress preload across Dry, Zinc, Oil, and Anti-Seize.

Nominal Size: #10-24 UNC
Grade / Class Dry (K=0.20) Zinc (K=0.18) Oil (K=0.15) Moly (K=0.12) Clamp (kN) Proof (kN)
Grade 5 4.799 Nm
3.54 ft-lb
4.319 Nm
3.186 ft-lb
3.599 Nm
2.655 ft-lb
2.879 Nm
2.124 ft-lb
4.972 6.629
Grade 8 6.775 Nm
4.997 ft-lb
6.097 Nm
4.497 ft-lb
5.081 Nm
3.748 ft-lb
4.065 Nm
2.998 ft-lb
7.019 9.359
18-8 Stainless CURRENT 2.541 Nm
1.874 ft-lb
2.287 Nm
1.687 ft-lb
1.906 Nm
1.405 ft-lb
1.524 Nm
1.124 ft-lb
2.632 3.51

Frequently Asked Engineering Questions (#10-24 UNC 18-8 Stainless)

What is the recommended tightening torque for a #10-24 UNC 18-8 Stainless bolt?
For a #10-24 UNC 18-8 Stainless Steel (ASTM F593 Group 1) bolt torqued to 75% of proof load, the standard dry (unplated, K=0.20) tightening torque is 2.541 N·m (1.874 ft-lbs / 22.49 in-lbs). If lubricated with light machine oil (K=0.15), torque must be reduced to 1.906 N·m (1.405 ft-lbs). Under anti-seize paste (K=0.12), the recommended torque is 1.524 N·m (1.124 ft-lbs). Failure to reduce torque when lubricating causes bolt over-stretching or thread stripping.
What tap drill size should be used for tapping #10-24 UNC internal threads?
The standard cut tap drill size for #10-24 UNC is #25 (0.1495 in) (0.1495" / 3.797 mm), which delivers approximately 89.8% theoretical thread engagement. For extremely tough parent alloys (e.g. titanium, 17-4 PH stainless, Inconel), a 50% engagement drill of 4.252 mm is recommended to prevent tap binding and breakage without compromising joint pull-out strength.
What clamp preload and proof load does a #10-24 UNC 18-8 Stainless fastener develop?
With a tensile stress area (As) of 11.311 mm² (0.01753 in²) and a nominal proof stress of 310.3 MPa (45,000 psi), a #10-24 UNC 18-8 Stainless fastener possesses an ultimate proof load of 3.51 kN (789 lbf). At the standard 75% proof preload threshold, the fastener exerts a clamping force of 2.632 kN (591.8 lbf) across the joint interface.
What clearance hole diameters should be drilled for #10-24 UNC bolts?
Per ASME B18.2.8 (Clearance Holes for Bolts, Screws, and Studs), recommended clearance hole diameters for a #10-24 UNC fastener are: Close Fit = 5.182 mm (0.204"), Normal Fit = 5.613 mm (0.221"), and Loose Fit = 5.944 mm (0.234"). Normal fit is standard for general machinery assemblies, while Close fit is reserved for high-precision dowel-aligned flanges.